Page 16
ENGLISH
AquaLink Touch
Thu January, 2009 3:03 PM
Pool Temp
Air Temp
86º
78º
FILTER
SPA
POOL
SPA
AUX1
AUX2
AUX3
Other
Devices
PUMP
HEAT
HEAT
On/Off
Home
Menu OneTouch
Help
Back
Status
Photos
Power
Green - Enabled
Red - On
Figure 11. AquaLink RS to Jandy JRT Heat Pump - T-Stat (2 wire) connection
AquaLink Touch
Thu January, 2009 3:03 PM
Pool Temp
Air Temp
86º
78º
FILTER
SPA
POOL
SPA
AUX1
AUX2
AUX3
Other
Devices
PUMP
HEAT
HEAT
On/Off
Home
Menu OneTouch
Help
Back
Status
Photos
Power
OR
OR
®
JANDY AquaLink RS
06/26/04 MON
6:00 PM
FILTER PUMP OFF
AIR 79°
EQUIPMENT ON/OFF
ONETOUCH ON/OFF
MENU / HELP
4-Conductor
Wire
RED
BLK
YEL
GRN
Jandy JRT Heat Pump Power Interface
Figure 12. Jandy JRT Heat Pump to Power
Center - RS485 (4 wire) connection
Jandy
®
JRT Series Heat Pumps
Green - Enabled
Red - On
4 3 2 1
4 3 2 1
S1
S1
RESET
OFF
ON
AUTO
SERVICE
TIME OUT
S2
DIP Switches
OFF
ON
S2
S1 and S2
4 3 2 1
4 3 2 1
4 3 2 1
6 5 4 3 2 1
10 9 8 7 6 5 4 3 2 1
S1
RESET
RS6 & RS8 ONLY
RS8 ONLY
POOL MODE
AUTO
SPA MODE
SERVICE
SPA DRAIN
HEATER
SOLAR
TIME OUT
SPA FILL
S2
OPTIONAL
RS Power
Center
|
Installation and Operation Manual
Heat Pump
Heat Pump Connections
Terminals 1 and 2
6 5 4 3 2 1
10 9 8 7 6 5 4 3 2 1
RS6 & RS8 ONLY
RS8 ONLY
POOL MODE
SPA MODE
SPA DRAIN
HEATER
SOLAR
SPA FILL
RS485 (4 wire) Connection to AquaLink
Using an Aqualink RS control and RS485 connection
will allow you to control both the heating and cooling
function with the remote.
1.
Confi rm the Jandy JRT heat pump and AquaLink
RS software revisions are compatible.
Jandy JE Heat Pump
Power Interface Software
Rev.
3.0 or Later
NOTE Only a revision "N", or higher, program chip in
the RS system will support the
pump interface.
2.
Turn off the power to both the heat pump and
the RS control and open the RS Power Center
enclosure and remove the front dead panel.
3.
Remove the two (2) screws holding the bezel in
place and turn the bezel over to view the circuit
board on the back.
4.
Locate the programmed chip on the Power Center
Board. In the center of the chip is the revision
letter. If the revision letter is "
step 5. If the revision level is "
replace the board or connect as shown in Section
4.5
5.
Use 22 gauge 4-conductor wire (Zodiac
4278) to run between the heat pump and the RS
control, and match the wire color order.
Connector for Low
Voltage Wires
RS
®
AquaLink
RS Software
®
Revision
N or Later
Jandy JRT
heat
" or higher go to
N
" or lower,
MMM
Part No.
®