TMB QUICK P12 Manual De Uso Y Mantenimiento página 21

N.B. :
appliance.
N.B. :
careful not to rip it. If the bag is made of paper, dispose of it properly, but if it is made of
fabric just empty it.
N.B. : If there is the rapid emptying kit, proceed as follows:
Remove the discharge hose from the catch of the collection tank
• Unscrew the cap and place the hose on the discharge surface and gradually release
the hose
6.
AT THE END OF THE WORK
At the end of the work, and before carrying out any type of maintenance, perform the following
operations:
1. Take the appliance to the place where it is maintained and carry out all the procedures listed in the
MAINTENANCE".
2. Take the appliance to the designated machine storage place.
3. Take all necessary steps to ensure that the device is in a safe condition (see
ATTENTION:
there must be no objects that could either damage it, or be damaged through contact with it.
MAINTENANCE
operating, to carry out maintenance do as follows:
1. Take all necessary steps to ensure that the device is in a safe condition (see
2. Remove the vacuum head (1) using the handle, before removing the head loosen the locking hooks
(2) on the side of the collection tank (3) (Fig.1
3. Fig.2
damp cloth (Fig.3
N.B. :
clean it thoroughly, and if necessary wash it in water.
ATTENTION:
clogged or if it is damaged replace it.
4.
thoroughly with a normal soft brush, if necessary, wash it in water.
them with a jet of air and check their state of preservation, replace them if necessary.
1
3
1
1.
head, remove the caseback (8) and clean the whole. When dry reassemble by running on
the contrary operations.
replace them if necessary.
2. Clean the inside of the collection tank with a damp cloth.
3. Put back the vacuum head (1) on top of the collection tank (3), remembering to secure it with the
hook catches (2).
4. Disconnect the vacuum hose from the vacuum nozzle on the collection tank, before pulling the
vacuum hose press the release button.
5. Clean the inside of the vacuum hose with a jet of compressed air, if necessary removing any
obstructions.
6. Disconnect the cleaning accessory.
7. Clean the inside of the vacuum chamber of the accessory with compressed air, and if necessary
remove any obstructions.
3
"MACHINE SAFETY").
"MACHINE SAFETY").
2
4
2
5
6
8
7
TROUBLESHOOTING
This chapter lists the most common problems linked with the use of the appliance. If you are unable to
resolve the problems with the information given here, please contact your nearest assistance centre.
PROBLEM POSSIBLE CAUSE
The main switch is not activated.
The plug on the appliance's power
cable has not been correctly inserted
into the mains socket.
appliance do not match the electrical
network.
The power cable is damaged.
The vacuum hose is not connected
correctly to the nozzle on the
collection tank.
The vacuum hose is not connected
correctly to the extension hose.
The extension hose is not connected
correctly to the vacuum accessory
being used.
The vacuum circuit
(vacuum hose; extension
vacuum accessory).
There is a blockage in the vacuum
DISPOSAL
To dispose of the appliance, take it to a demolition centre or an
authorised collection centre.
Before scrapping the appliance, it is necessary to remove and
separate out the following materials, then send them to the
appropriate collection centres in accordance with applicable
environmental hygiene regulations:
• Electric and electronic parts*
• Plastic parts (tanks and handlebars)
• Metal parts (levers and frame)
(*) In particular, contact your distributor when scrapping electric
and electronic parts.
EC DECLARATION OF CONFORMITY
The undersigned manufacturer:
Via Cà Nova Zampieri n.5
37057 San Giovanni Lupatoto (VR)
Declares under its sole responsibility that the products
ASPIRAPOLVERE/ASPIRALIQUIDI:
QUICK P12 ; QUICK P25 ; QUICK P35 ; QUICK A11 ; QUICK A27 ; QUICK P30 ; QUICK P60 ;
QUICK P80
They comply with the provisions of the Directives:
• 2006/42/CE
• 2014/35/EU
• 2014/30/EU
• 2011/65/UE
Via Cà Nova Zampieri n.5
37057 San Giovanni Lupatoto (VR) - ITALY
21
SOLUTION
Press the main switch.
Connect the plug on the appliance's
power cable to the mains socket.
Check that the technical data on the
appliance's serial number plate match
the data of the mains supply.
Contact a specialised technician
immediately.
Connect the vacuum hose correctly to
the nozzle on the collection tank.
Connect the vacuum hose correctly to
the extension hose.
Connect the extension tube correctly
to the vacuum accessory being used.
is blocked
Remove the obstruction in
hose;
vacuum circuit.
Clear the obstruction in the vacuum
TMB s.r.l.
San Giovanni Lupatoto (VR), 04/06/2018
The legal representative
the
TMB s.r.l.