Genie 41486R Guia De Inicio Rapido

41641.00507, 10/2020
INTELLICODE®
315/390MHZ SINGLE DOOR
EXTERNAL RECEIVER KIT
Specifications:
Remote Capacity: 64
Voltage/Current/Hz:
- Power Pack: 100-240VAC, 0.5A, 50-60Hz
- Power Pack Output: 12VDC, 1A
- Receiver Input Voltage: 9-42VDC, 200mA, 50-60 Hz
or: 9-30VAC, 200mA, 50-60 Hz
0 0
- Temperature Range: -30 F to 158
!
MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH.
• Wall Console must be mounted in sight of door, at least 5 feet above floor and clear of moving parts.
• Keep people clear of opening while door is moving.
• DO NOT allow children to play with the remote or door operator.
If SAFETY REVERSE does not work properly:
• Close door then disconnect operator using the manual release handle.
• DO NOT use remote controls to operate door.
• Refer to Door and Door Operators Owners Manuals before attempting any repairs.
AVERTISSEMENT
!
UNE PORTE EN MOUVEMENT PEUT CAUSER DE GRAVES BLESSURES, VOIRE LA MORT.
• N'installez PAS le transmetteur à moins que l'appareil de sécurité du dispositif de fermeture de porte ne fonctionne
conformément au manuel du dispositif de fermeture de porte. La console murale doit être montée à la vue de la
porte, à au moins 5 pieds au-dessus du sol et il ne doit y avoir aucune pièce de porte en mouvement à proximité.
• Éloignez les gens de l'ouverture lorsque la porte est en mouvement.
• NE permettez PAS aux enfants de jouer avec le transmetteur ou le dispositif de fermeture de porte.
Si l'inversion de sécurité ne fonctionne pas correctement :
• Fermez la porte, puis déconnectez le dispositif d'ouverture à l'aide de la poignée de dégagement manuel.
• N'utilisez PAS le transmetteur ni le dispositif de fermeture de porte.
• Référez-vous aux manuels du propriétaire de la porte et de l'ouvre-porte avant de tenter toute réparation.
FIG. 1. Residential/commercial or gate operator powered with 115VAC
power pack.
Power
Pack
NOT POLARITY SENSITIVE
FIG. 2. - Four-Wire commercial door or gate operator powered from
operator.
Operator
Terminals
24V 24V
Power Common
NOT POLARITY SENSITIVE
FIG. 3. - Three-Wire commercial door or gate operator powered from
operator.
Operator
Terminals
24V 24V
Power Common
1.750
4.670
4.000
F
5.662
WARNING
POWER
9-42VDC
DOOR 1
9-30VAC NO C
Operator
Terminals
1/4"
Push Button
split & strip wire
POWER
9-42VDC
DOOR 1
9-30VAC
NO C
1/4"
split & strip wire
Push Button
POWER
9-42VDC
DOOR 1
9-30VAC NO C
1/4"
split & strip wire
Push Button
IMPORTANT NOTICE: This kit may only be used on an operator manufactured 1993
and later with working safety sensors.
PRE-INSTALLATION: For use on momentary contact capable units only
• If existing receiver will no longer be used, erase remotes. Refer to operator owners
manual, if needed.
• Determine power source and wire to receiver using figures 1, 2 or 3. Refer to
operator owners manual, if needed.
INSTALLATION:
1. Unplug or turn off breaker that supplies power to operator.
5.334 2. Find a suitable mounting point for receiver within a few feet of the operator.
3. Mount receiver to wall or ceiling. Due to variations in mounting methods,
hardware is not included.
4. Strip ends of included bell wire and install between receiver and residential (Fig.
1.338
1-A) or commercial operator connections. If using the recommended power
supply, plug connector from power pack into receiver (FIG. 1). To wire for an
alternate power supply in a commercial application, see
FIG. 2-3.
5. Install coax antenna on to receiver coax connector.
6. If using 115VAC power pack, plug power pack into
standard 115VAC outlet.
7. Use included staples to tidy any hanging wires.
8. Restore power to operator.
WARNING
!
During programming, the door operator
could begin to run. Stay away from
moving door and its parts. To prevent
door from moving, close door using
the wall button and disconnect it from
operator by pulling Emergency Release
Cord (See owners manual).
NOTE: Programming must be completed with 30 seconds upon pressing programming
(LEARN) button or receiver will turn off remote pairing mode. Press LEARN button again to
enable pairing mode and resume programming remote.
NOTE: If receiver does not perform properly, check connections between power source and
receiver and connections between receiver and operator.
PROGRAMMING INTELLICODE® REMOTE:
Remove tab to activate remote control
1. Press the LEARN button on the receiver. (LED begins flashing).
2. Press the remote button once. (LED will change to solid).
3. Press the remote button a second time (LED will turn off ).
4. The next remote button press will activate the receiver.
6.35mm
NOTE: If receiver LED flashes rapidly for 5 seconds then receiver memory is
full. Erase remotes to enable programming.
Clearing All Remotes:
1. Press and hold the LEARN button. (LED changes to solid).
2. After approximately 20 seconds the red LED will flash three times. Release the
LEARN button. All remotes have been cleared from the receiver.
REPLACE REMOTE BATTERY WITH CR2032 COIN CELL BATTERY.
1.
Open the remote case using a washer or coin that fits into the slot at the top of the
remote.
2.
Replace battery. Match battery polarity symbols inside battery housing.
3.
Align components and snap case closed.
6.35mm
For assistance contact the Genie Company at 1-800-354-3643
FCC Part 15.21 Statement:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
6.35mm
FCC / IC Statement:
This device complies with FCC Part 15 and Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation of the device.
WARNING
!
Durant la programmation, l'ouvre-porte
pourrait commencer à fonctionner.
Restez éloigné de la porte en
mouvement et de ses pièces. Pour
empêcher la porte de se déplacer, fermez
la porte à l'aide du bouton mural et
débranchez-la de l'appareil en tirant sur
la corde de déverrouillage de secours
(Référez-vous au guide du propriétaire).
For Patent Information:
www.geniecompany.com/patents,
©2020, The Genie Company
Push button operator
terminal examples:
STB BWC
1 2 3 4
1 2 3 4
Fig. 1-A