LUND 67790 Manual Del Usuario página 10

GB
it can be helpful for further transport and storage of the product.
Check the product for damage. If any damage is detected, do not use the product until the damage has been repaired or the
damaged components replaced with new ones that are free of defects.
Clean the product according to the instructions specifi ed in the "Product Maintenance" section.
Caution! Make sure that the power cord is unplugged from the socket, before attempting to install or remove the stirrers.
Select a pair of identical stirrers. It is forbidden to use diff erent stirrers at the same time. The stirrers are paired-up so that they
can work together. Using two diff erent stirrers will cause them to block each other, which can damage the stirrers and the blender,
and cause fi re and/or electrical shock.
The stirrer handles have small tabs, which must be inserted into the notches in the stirrer socket of the blender (II). The stirrer
is fastened by a snap-in mechanism when a characteristic "click" is heard. Properly fi tted stirrer does not fall out of the socket
automatically, and its disassembly is possible only after pressing the "EJECT" stirrer lock button (III).
After fi xing the stirrers, make sure that the on/off switch is in the "off " position, marked "0" (zero).
The blender can also be used together with the supplied bowl and base. In this case, there is no need to hold the blender in your
hand all the time. This can prove useful for long mixing. Place the base on a fl at, level and hard surface. Mount the blender without the stirrers on the base so that the latches on the
front of the blender socket hit the openings in the blender housing fi rst (IV). Then push down the rear part of the blender so that
the latch engages (V). A correctly mounted blender cannot be removed from the socket otherwise than by pressing the blender
lift lock button (VI).
Press and hold the blender lift lock button (VII), lift the socket with the blender mounted, and then release the blender lift lock
button. The blender will be locked in the upper position.
Mount the selected stirrers in the same manner as when attaching directly to the blender.
Place the bowl in the bowl socket (VIII), then lower the blender by pressing and holding the blender lift lock button. The gears
around the edge of the bowl and at the base hinge should interlock (IX). When lowering the blender, the gears may block each oth-
er and not allow the blender to be fully lowered. In this case, turn the bowl slightly by hand until the gears stop blocking each other.
Product operation
Mount the selected pair of same-type stirrers or mount the blender and bowl in the base.
Check that the on/off switch is in the position marked "0" (zero).
When using the blender without a base, grasp the blender by the handle so that the stirrers do not come into contact with any
object. If the base will also be used, lower the blender to the bottom position.
Plug the power cord plug into the socket.
Make sure that the stirrers are not in contact with any object, move the on/off switch to the position marked "1" and check if the
stirrers and, possibly, the bowl are rotating freely. In case of any symptoms of improper operation, e.g. stirrers catching on each
other during rotation, increased noise, increased vibrations, immediately turn off the blender with the on/off switch, disconnect
the power cord plug from the socket and investigate the cause of improper operation, e.g. repeat the installation of the stirrers.
Stop using the blender if it is not possible to determine and eliminate the cause of improper operation. In such a case, contact an
authorised maintenance service of the manufacturer.
The on/off switch has several positions described by digits. The greater the setting digit, the higher the stirrers' rotation speed.
Press and hold the "TURBO" button to start the mixing process at the highest speed. Release the "TURBO" button to return to the
speed set in the on/off switch setting.
The whisk stirrers should be used to whisk the egg whites, whipped cream, butter, creams, etc. Do not use this type of stirrers to
mix hard food ingredients or dense masses. This may cause damage to the stirrer blades. It is forbidden to use damaged, e.g.
deformed or cracked, stirrers.
Spiral blenders can be used for whipping up dense masses or doughs.
Mixing should be carried out using vessels of suffi cient depth to avoid spillage of food ingredients. After mixing, fi rst turn the blend-
er off with the on/off switch, wait until the stirrers have stopped rotating completely and then pull them out of the mixed substance.
This will prevent spillage of food ingredients which would occur when pulling out the rotating stirrers from the vessel.
When mixing bulk ingredients, e.g. fl our, with liquids, stop mixing for a while and add bulk material in small portions, preferably
spreading it in a thin layer over the entire surface of the mixed liquid. The mixing should be resumed at the lowest speed and
possibly increased after the bulk ingredient has been mixed with the liquid. This will help reduce the occurrence of food ingredient
powder clouds.
It is not recommended to use the blender with only one stirrer installed. The blender is designed for use with a pair of stirrers and
using only one stirrer will lead to faster wear of the blender and can also cause damage to the blender.
Use only the stirrers supplied with the blender or approved by the manufacturer. Using other stirrers may damage the blender.
Product maintenance
CAUTION! Every time before cleaning, turn off the product, unplug the power cord plug from the socket, wait for the appliance to
cool down and then proceed with maintenance.
CAUTION! It is recommended to clean the stirrers immediately after all dishes have been prepared. This will prevent food residues
O R I G I N A L I N S T R U C T I O N S
10