Care And Maintenance - KIKKA BOO ANGELE Instrucciones De Uso

12. FOLD THE STROLLER
Fold the leg rest as gure 12a,and at the same time unlock the front wheels to keep the front wheels in the far direction from the rear wheels.
12b. Press the second lock to the left side at the same time press the folding lock,then press the handle to fold the stroller.
12c. Keep pulling the stroller handle down until you hear a "click"sound.
12d. Make sure the lock have been fully locked.
12e. After folding the stroller can stand as 12e.
13. USE THE SAFETY BUCKLE
Figure13a-13b: There are 2 position for safety belt, the up position is suitable for one baby more than 6 months, the bottom position is suitable for one baby under than 6
months.
Click here to lock the safety buckle on both sides as 13c.
Press the middle button to release the safety button as 13c.
You can adjust the length of the seat belt by pulling the safety buckle on both sides as needed.
14. Assemble the carrycot/ Removing the Carrycot:
14a. In order to unfold the carrycot remove the bedding and the mattress, and then squeeze the metal tensioners on the bottom plate of the carrycot n the direction of the
arrows( gure 14a), until it locks in special holders. You should hear a "click"sounds locking the tensioner in the holder.
The carrycot is designed for children up to 6 months old weighing up to 9 kg, which cannot seat, kneel or trundle by themselves. Stop using thecarrycot if your child starts
sitting kneeling or trundling by itself
WARING: Do not use an additional mattress of thickness of more than 15mm.
14b. Assemble every spare parts for the carrycot.
14c.The carrycot canopy has 4-step adjustment. In order to adjust it, press simultaneously the buttons located at the base of the canopy tube and adjust the desire
position. The carrycot has a special carrying handle. You can move the carrycot by holding the handle.
Make sure that the carrying handle is locked in the correct position before you move the carrycot.
14d. You can extend the canopy by pushing the canopy tube.
14e. Assemble the carrycot in the direction keeping the baby face to the adul.
The carrycot can be assembled only back to the direction of travel( in this setting, the person pushing the pram is face to face with a child)
Lock the safety brake before you assembly the carrycot on the stroller frame.
In order to assembly the carrycot on the stroller frame, remove the seat , then assemble the carrycot. You should hear a "click" as 1f .
Before using, make sure that the carrycot is properly assembled
Lock the safety brake before you remove the carrycot.
In order to remove the carrycot press simultaneously the buttons located on the adapters of thecarrycot and pull it upwards as 14e.
15. CAR SEAT. ASSEMBLY AND DISASSEMBLY IN GROUP 0+
Apply the brake before installing the seat. Remove the seat from the frame;
15a. Insert one of the chair adapters as shown in Figure 15a; Place the other on the other side 15b.
The adapter is universal for the basket and the car seat.
Install the car seat with the adapters that are part of its kit. Hold the adapters and mount them to the base of the stroller frame. You should hear a CLICK to complete the
assembly as Figure 15c.
Before use, make sure that the adapters and the seat are properly assembled.
• This product is suitable for children with a weight from 0 to 13kg.
• Only suitable for use in vehicles equipped with a three-point safety belt as approved by the ECE regulation No.16 or by other, comparable standards.
• All belts intended for fastening to the restrainer ttings in the vehicle must be tightened. The belts used to hold the child must be fastened tightly. The belts may
furthermore not be twisted.
• It is essential to ensure that the crutch belts are fastened as low as possible to ensure that the crutch is retained properly.
• Replace the restrainer ttings if they have been subject to heavy loading due to an accident.
• It is dangerous to change or supplement the restrainer ttings in any way without approval from the competent authorities and to not precisely observe the assembly
instructions for restrainer ttings issued by the manufacturer.
• Do not expose the seat to direct sunlight.
• Do not leave your child unattended in the restrainer ttings.
• Do not use the child restrainer ttings without seat cover.
• The seat cover is an integral part of the restrainer ttings and may not be exchanged for any other than that stated by the manufacturer.
• Rigid parts and plastic parts must not be jammed during assembly.
• This product does not comply to the requirements of EN 12790 for reclined cradles!
• Never use this product as reclined cradle.

CARE AND MAINTENANCE

• Please note the textile label on product. • Please check on a regular basis that the brakes, wheels, latches, connecting elements, belt systems and seams are properly
functional. • Do not expose the product in strong sunshine. • After use in rain or snow, the wheels should be lubricated and the vehicle dried to prevent rust. • Care for, clean
and check this product regularly. • Do not use accessories that have not been approved by the manufacturer.
ENGLISH