Hozelock Cyprio EASYCLEAR 6000LV Manual Del Usuario página 7

33856 EASYCLEAR 6000lv UI's(29-8-8)
independently adjusted using the Fountain
Adjuster (Fig 3B-N) and Waterfall Adjuster (Fig
3A-O).
Install and position the pump as previously
described and switch on.
Waterfall Only Operation
(Fig 4 for general installation guide)
Screw the blanking plug onto the fountain outlet
(Fig 3A-P).
Attach a suitable length (3m maximum) of 25
mm (1") hose to the hose tail on the Waterfall
Adjuster (Fig 3A-O) and secure with a suitable
hose clip and position the outlet end of the hose
in the desired position.
Screw the Waterfall Adjuster onto the waterfall
outlet on the front of the EasyClear™ (Fig 3A-Q).
Adjust the flow using the Waterfall Adjuster, (Fig
3A-O), to suit your needs.
Install and position the pump as previously
described and switch on.
UVC Operation
The UVC will automatically switch on once the
unit has been connected to the electricity supply.
The UVC lamp can be checked for operation by
looking for a bluish glow from ball joint outlet
(Fig 1-A). Please note that this may only become
visible in low light conditions.
See Maintenance section for Lamp replacement.
Maintenance
The Hozelock Cyprio EasyClear™ has been
designed to allow fast and easy maintenance. As
with all pond equipment, occasionally it will
become necessary to clean or replace parts. Refer
to the safety sections before attempting any
maintenance.
Fountain Head (Fig 1-E)
Follow the below procedure if the fountain head
is blocked:
1 - Place a coin or similar in the slot and gently
lever off the fountain head (Fig 1-G).
2 - Rinse in clean water and reassemble.
Foam
Follow the below procedure if flow appears
reduced:
29/8/08
All manuals and user guides at all-guides.com
14:16 Page 7
1 - Release the Foam Cover by pushing the two
buttons (Fig 5-R) and lift the cover (Fig 6-S).
2 - Remove the Foam (Fig 7-T). Note:- If the unit
is out of the pond for more then 20 minutes the
biological filter action may stop working.
3 - The Foam Cover and Base should also be
rinsed.
4 – It may also be necessary to clean out the
biomedia and stones (Fig 7-U) if these have
become clogged.
5 - Reassemble the Filter.
Quartz Tube
Follow the below procedure if your pond
remains green:
1 - Remove the bayonet locking screw (Fig 8-V),
twist and lift the bayonet tube (Fig 8-W).
2 - Clean the Quartz Tube. Take extra care when
handling the Quartz tube. In hard water areas,
the quartz tube may become covered in
limescale, which will reduce efficiency. Clean the
tube with a soft cloth and a gentle de-scaler
(such as vinegar and water), rinse in water before
refitting.
3 – Reassemble the bayonet tube and restart (Fig
8-X).
Warning! Ensure that the quartz tube is not
damaged before refitting.
Lamp Replacement
Follow the below procedure if the lamp needs
replacing or does not illuminate:
Change the lamp at the start of the new season.
Even though the lamp still glows it may not be
giving out any useful UV radiation. How well
the EasyClear™ performs is related to the
strength of the UV radiation produced. This will
slowly decline from the day your lamp is
switched on. The UVC lamp has an effective life
of 12 months. You need to change the lamp
when there is a significant reduction in water
clarity. Make sure this is due to an expired lamp
and not a badly maintained filter or a
dirty/limescaled quartz sleeve. Both can greatly
reduce UV transmission into the water.
1 - Remove the bayonet locking screw (Fig 8-V),
twist and lift the bayonet tube (Fig 8-W).
2 - Remove the quartz tube, rotating the plastic moulding anticlockwise and lifting up and away
(Fig 9-Y).
3 - With the lamp now accessible pull it out of
the holder (Fig 9-Z) and push in a new lamp.
4 - Reassemble the bayonet tube and restart (Fig