Tabla de contenido
Idiomas disponibles
Idiomas disponibles
users.
▶Maintain power tools. Check for misalignment or jammed moving
parts, breakages and any other condition that might affect the power
tools operation. If it is damaged, the power tool must be repaired.
Many accidents are caused by poorly maintained power tools.
▶Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to jam and are easier
to control.
▶Use the power tool, accessories and cutting tools etc. in accordance
with these instructions, taking into account the working conditions
and the work to be performed. Use of the power tool for operations
different from intended could result in a hazardous situation.
5) SERVICE
Your power tool shoul be serviced by a qualiified specialist using only
standard spare parts. This will ensure that it meets the required safety
standards
SPECIAL SAFETY WARNINGS FOR AIR
PUMP
▶Inspect the Air Pump before use and do not use if any of the
components are broken, burnt, melted, wet or damaged
▶Check the tyre pressures before inflating so as not to exceed the
rated pressure as the tyres may burst if overinflated.
▶Do not use the Air Pump on high pressure tyres such as those used
on commercial vehicles, agricultural or specialist vehicles.
▶Do not kink or block the air hose while the Air Pump is working.
▶Keep the car engine running when using the Air Pump otherwise the
car battery will run out.
▶Know your Air Pump. Read operator's manual carefully. Learn its
applications and limitations, as well as the specific potential
hazards related to this tool. Following this rule will reduce the risk
of electric shock, fire or serious injury.
▶Do not use the Tyre inflator when the vehicle is moving.
▶The Air Pump is not designed for continuous use. Operation over an
extended period of time will overhead and damage the Air Pump. It
should not be used continuously for more than 30 minutes. After 10
minutes, turn it off and let it cool for 15 minutes before resuming
operation.
▶Inspect unit for cracks, pin holes, or other imperfections that could
cause the Air Pump to become unsafe. Never cut or drill holes in
the Air Pump.
▶Make sure the hose is free of obstructions or snags. Entangled or
snarled hoses can cause loss of balance or footing and may become
damaged.
▶Use the Air Pump only for its intended use Do not alter or modify the
unit from the original design or function.
▶Always be aware that misuse or improper handling of this Air Pump
can cause injury to yourself and others.
Instruction manual
▶Never leave a Air Pump unattended with the air hose attached to the
item being inflated.
▶Do not continue to use a Air Pump or hose that leaks air or does not
function properly.
▶Always disconnect the air supply and power supply before making
adjustments, servicing or when the unit is not in use.
▶Do not attempt to pull or carry the Air Pump by the hoses.
▶Always follow all safety rules recommended by the manufacturer.
Following this rule will reduce risk of serious personal injury.
▶Do not use as a breathing device.
▶Never direct a jet of compressed air toward people or animals. Take
care not to blow dust and dirt towards yourself or others. Following
this rule will reduce the risk of serious personal injury.
▶Protect your lungs. Wear a face or dust mask if the operation is
dusty. Following this rule will reduce the risk of serious personal
injury.
▶Do not use this unit to spray chemicals.
▶Check damaged parts. Before further use of the air pump, a guard or
other part that is damaged should be carefully checked to determine
that it will operate properly and perform its intended function. Check
for alignment of moving parts, binding of moving parts, breaking
of parts, mounting and any other conditions that may affect its
operation.
▶Risk of Bursting. Carefully monitor objects during inflation.
▶To reduce the risk of over inflation, use a reliable pressure gauge
periodically during inflation. The pressure gauge on the air pump is
for reference only and is therefore not binding for exact values.
ADDITIONAL SAFETY INSTRUCTIONS FOR
BATTERIES AND CHARGES
1) BATTERIES
▶Never attempt to open for any reason.
▶Do not store in locations where the temperature may exceed 40ºC.
▶Charge only at ambient temperatures between 4ºC and 40ºC.
▶When disposing of batteries, follow the instructions given in the
section "Protecting the environment".
▶Do not cause short circuits. If connection is made between the
positive (+) and negative (-) terminal directly or via accidental
contact with metallic objects, the battery is short circuited and an
intense current will flow causing heat generation which may lead to
casing rupture or fire.
▶Do not heat. If batteries are heated to above 100ºC, sealing and
insulating separators and other polymer components may be
damaged resulting in electrolyte leakage and/or internal short
circuiting leading to heat generation causing rupture or file.
Use only batteries and charges applicable for this
machine.
ref. 08782
ES
PT
EN
FR
Tabla de contenido
