Genie ACSCTG Instrucciones

41711.00670, 02/2021
NOT FOR USE WITH ANY GARAGE DOOR OPENER MANUFACTURED PRIOR TO 1993.
SAFETY BEAMS (PHOTOCELLS) MUST BE IN PLACE AND OPERATIONAL.
WARNING
!
MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH.
• DO NOT install transmitter unless the door operator's safety device works as required by the
door operator's manual.
• Wall Console must be mounted in sight of door, at least 5 feet above floor and clear of moving
door parts.
• Keep people clear of opening while door is moving.
• DO NOT allow children to play with the transmitter or door operator.
If safety reverse does not work properly:
• Close door then disconnect opener using the manual release handle.
• DO NOT use transmitter or door operator.
• Refer to Door and Door Opener Owner's Manuals before attempting any repairs.
AVERTISSEMENT
!
UNE PORTE EN MOUVEMENT PEUT CAUSER DE GRAVES
• N'installez PAS le transmetteur à moins que l'appareil de sécurité du dispositif de fermeture de
porte ne fonctionne conformément au manuel du dispositif de fermeture de porte. La console
murale doit être montée à la vue de la porte, à au moins 5 pieds au-dessus du sol et il ne doit y
avoir aucune pièce de porte en mouvement à proximité.
• Éloignez les gens de l'ouverture lorsque la porte est en mouvement.
• NE permettez PAS aux enfants de jouer avec le transmetteur ou le dispositif de fermeture de
porte.
• Si l'inversion de sécurité ne fonctionne pas correctement :
• Fermez la porte, puis déconnectez le dispositif d'ouverture à l'aide de la poignée de dégagement
manuel.
• N'utilisez PAS le transmetteur ni le dispositif de fermeture de porte.
• Référez-vous aux manuels du propriétaire de la porte et de l'ouvre-porte avant de tenter toute
réparation.
THINGS TO KNOW BEFORE STARTING:
• During programming, the garage door opener may operate. Ensure that the
garage door opening is clear of personnel or any obstructions.
• Do not to press the LEARN button for longer than the noted 2-3 seconds as it
could cause your existing, operational remotes and keypads to no longer work.
• All buttons are factory set to Genie Intellicode® 1.
Below are the brands and specifications that this remote is compatible with. Find the
ID# in Chart A below that references your specific opener specification. You will need
this number during programming. Refer to STEP 1 to find the type and/or LEARN/
PROGRAM button.
Chart A
AVAILABLE PROGRAM METHOD
Brand Name Specification Notes
Genie® 315/390 MHz, Intellicode® I, 1995-current
Overhead Door® 315/390 MHz, CodeDodger® I, 1995-current
Purple Learn Button, Security +®, 2006-2014, 315 MHz
Chamberlain®
Orange/Red Learn Button, Security +®, 1996-2005, 390 MHz
LiftMaster®
CraftsMan®
Yellow Learn Button, Security +2.0®, 2011-current, 390 MHz
Green Learn Button, Billion Code®, 1993-1995, 390 MHz
Genie® 315/390 MHz, Intellicode® II, 2010-2011
Overhead Door® 315/390 MHz, CodeDodger® II, 2010-2011
Sommer® 310 MHz, Rolling Code
Linear® 318 MHz, Mega Code®
Wayne Dalton® 372.5 MHz, Rolling Code, 1999-current
Ryobi® 372.5 MHz, Rolling Code
Guardian® 303 MHz, Fixed Learn Code
Xtreme® brand 303 MHz, Fixed Learn Code
Marantec® 315 MHz, Fixed Learn Code
FAAC® 433.92 MHz, Rolling Code
Genie® and Intellicode® are registered trademarks of The Genie Company. All other listed names and trademarks
are the property of their respective owners.
NOTE: During programming, the garage door opener will operate. Ensure that
the garage door opening is clear of personnel or any obstructions.
STEP 1 - Find Specifications & Learn Button
1. Locate the brand and opener/receiver specifications for your device by consulting the label on the
opener/receiver, the instruction manual, the current remote controls for the opener, or the original
manufacturer of the opener/receiver.
2. Find the LEARN/PROG button on your device - shape, color or name of this button could vary by
brand. For garage door openers, be sure to check under the light covers. For commercial or gate
openers, this button may be on the circuit board of the opener. In some cases, this button could
also be on an external receiver that is mounted on or nearby the product. Consult the devices
manual if needed.
*For Marantec® openers, reference operator manual to program remotes to the operator head.
EXAMPLES:
PRGM
SET
UNIVERSAL 2-BUTTON REMOTE
INSTRUCTIONS
BLESSURES, VOIRE LA MORT.
LEARN METHOD ID#
RADIO
SIGNAL
LEARN
CODE
Gate
Receivers
STEP 2 - Activate Remote/Button Layout & LED
STEP 3 - Programming Remote
IMPORTANT: For ID#4 Chamberlain®/LiftMaster®/Craftsman® Yellow Learn Button -
move immediately to the proper section below. For all other ID#s, proceed to LEARN
METHOD section.
LEARN METHOD
Review Chart A to find your specifications and available programming options. Each
button can be programmed individually to operate up to 2 different brands of garage
door openers and gate receivers.
1. Remove activation tab from inside battery compartment.
2. Find and remember the required number of button presses (ID#) in the LEARN
METHOD column next to your brands/specification in Chart A.
REMEMBER: For ID#4 Chamberlain®/LiftMaster®/Craftsman® Yellow Learn Button
ONLY - Move immediately to instructions below. For all other ID#s, proceed to step 3.
3. On remote, press and hold down BOTH buttons at the same time – as soon as the
RED LED begins flashing, immediately release both buttons (@ 5 seconds).
4. On remote, press button of your choice the required number of times from CHART
A.
5. When presses are complete, simply WAIT until the GREEN LED blinks and then goes
out.
6. On opener, press LEARN/PROGRAM button for 2-3 seconds and then release.
7. Press and release button you just programmed once every 2 seconds until the
garage door opener operates.
8. Test the button - programming is complete.
TIP: Allow the LED light on the universal transmitter to stop flashing before your next
button press.
ONLY for ID#4 Chamberlain®/LiftMaster®/Craftsman® Yellow Learn:
1. Remove activation tab from inside battery compartment.
2. On remote, press and hold down BOTH buttons at the same time – as soon as the
RED LED begins flashing, immediately release both buttons (@ 5 seconds).
3. On remote, press button of your choice four times.
4. When presses are complete, simply WAIT until the GREEN LED blinks and then goes
out.
5. On remote, press and hold down the button you just chose until the GREEN LED
blinks and goes out again – then release (@5 seconds).
6. On opener, press LEARN/PROGRAM button for 2-3 seconds and then release.
7. Press the remote button you chose ONE time. Opener will click.
8. On the opener, press the LEARN/PROGRAM button again for 2-3 seconds then
release.
9. Press the remote button you chose ONE time again. Opener will click again.
10. Press the remote button again and the opener will activate.
11. Test the button - programming is complete.
Number of TIP: Allow the LED light on the universal remote to stop flashing before your next
Button Presses (ID#)
button press.
1
1
Clearing Remote
2
3
Clearing out the remote
4
To clear any existing programming from the remote, perform the following:
5 1. Press and hold down BOTH buttons at the same time – continue holding down
both buttons until the GREEN LED blinks and goes out (@10 seconds).
6
6 Installing Visor Clip - Changing Batteries
7
Visor Clip
8
Insert visor clip to any of the 4 slots in back of case dependent on
9
mounting preference.
10
Change Battery
11 Remove visor clip and screw from back of remote.
Pry case open with small coin or screwdriver.
11
Replace battery with CR2032 coin cell.
12
13
Programming Assistance:
If the opener does not activate after the steps shown, repeat steps or
contact Customer Care by website chat (www.geniecompany.com)
or by phone at: 1-800-354-3643 for programming assistance.
You may also scan this QR code for additional information and links.
For Patent Information: www.geniecompany.com/patents, ©2021, The Genie Company
FCC Part 15.21 Statement:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
FCC / IC Statement:
This device complies with FCC Part 15 and Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
LEARN
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
CODE
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Activation Tab: Pull tab to activate the remote.
LED - The LED will light with each button press and will also light
in response to button presses during different programming
modes.