Silverline 265438 Manual Del Usuario página 7

GB
Notes
• It is normal for the Heating Indicator (4) to regularly illuminate during use to restore
steam pressure. Wait until the Heating Indicator turns off before continuing use. This will
take approximately 40 seconds
• The steam cleaner body will become very hot in use. Move the steam cleaner by using
the Carrying Handle (8). Do not use the Hose (11) to pull the steam cleaner
• When using the Extension Tubes each time you stop operating the Trigger some water
may cool in the Extension Tubes and be released as water when you start operating
the Trigger again. It may be necessary to keep a cloth handy just to capture this water
before steam is restored
• The Pressurised Tank Cap (5) cannot be unscrewed when the steam cleaner is
pressurised. Do not attempt to unscrew as it may be damaged if forced
• Do not store the cleaner where it will be exposed to freezing temperatures
General cleaning
1. Apply steam, using appropriate accessories (see Application)
2. Once the dirt has been loosened it can be wiped away with a household cloth (Note:
metal surfaces may become very hot whilst being steam cleaned)
Cleaning clothes
1. Use the Large Brush (12) with a cloth fitted
2. Hang clothes, and brush the steam back and forward gently over the clothes
Cleaning windows
• Do not use the steam cleaner on very cold glass
• If the windows are very dirty, clean with the Large Brush with a cloth fitted first. You can
then use the Squeegee (15)
1. Use the Squeegee, Accessory Connector (19) and one or both Extension Tubes (22) if
required
2. Hold the Squeegee against the top of the window, press the Trigger (9) and move the
squeegee down the window
3. After cleaning, use a clean cloth to remove the dirt from the squeegee blade
Applications
As general guidance, this steam cleaner is suitable for cleaning the following surfaces and
materials. If in any doubt, always test a small inconspicuous area of the surface first.
Large surfaces: use the Large Brush (12)
• Carpets
• Tiled, parquet, stone and linoleum floors
• Tiled walls
• Roller shutters, guillotine windows
Small surfaces: use the Small Brush (16), Detail Brush (17) or Jet Nozzle (15)
• Small spaces in radiators
• Small areas of tiling
• Door and window frames
• Shutters
Glass surfaces: use the Squeegee (13)
• Windows and glass walls
• Glass doors
• Mirrors
Upholstery: use the Large Brush (12) with fitted cloth
• Curtains, carpets and mats
• Upholstered furniture (sofas, armchairs) – but see below
CAUTION: When cleaning furniture and other delicate surfaces
• Never clean with the direct jet
• Always fit a cloth to the Large Brush
• When you clean, do not exert pressure with the brush
Accessories
• Contact your Silverline stockist for additional or replacement accessories for this
product
• Only use accessories approved and designed for this product
6
All manuals and user guides at all-guides.com
Maintenance
WARNING: This steam cleaner has no user serviceable internal parts.
WARNING: Always disconnect from power supply before carrying out any maintenance/
cleaning.
Cleaning
• Keep the steam cleaner clean at all times. Dirt and dust will cause internal parts to wear
quickly, and shorten the machine's service life. Clean the body of your machine with a
soft brush, or dry cloth
Descaling
• To prevent the build-up of lime scale deposits in the tank use a proprietary descaler
solution suitable for a steam cleaner or a white vinegar solution. The frequency will
depend on the hardness level of your water supply. A very light deposit of lime scale
can be removed by pouring a small amount of descaler solution into the tank and
swilling the solution around the tank and pouring out. Then rinse the tank with clean
water. Frequent descaling is recommended to keep the steam cleaner in good operating
condition. A frequency of once a month is recommended for hard water areas. In
hard water areas it is recommended to empty the tank after use to help reduce the
build-up of scale.
Disposal
Always adhere to national regulations when disposing of electrical products that are no
longer functional and are not viable for repair
• Do not dispose of waste electrical and electronic equipment, with household waste
• Contact your local waste disposal authority for information on the correct way to dispose
of waste electrical and electronic equipment
Symptom Possible Cause
Abnormal operation steam cleaner not
switched on
tank has no or minimal
level of water
pressure hasn't reached
4Bar
Heating indicator not tank has no, or very
switching off little, water
Stops producing steam pressure level has
during operation dropped
tank has no, or very
little, water
Takes longer than first build-up of scale in tank
use to release steam
Handle connector, connector may be
extension tube or incorrectly fitted
accessory is leaking
steam
connector may be
blocked or dirty
connector seal may be
damaged
Steam cleaner is leaking tank over-filled
steam cleaner not on a
level surface
Note: This product features a thermostat and safety valve to protect against malfunction
or incorrect use.
• If the steam cleaner fails to operate after becoming excessively hot, switch off and allow
it to fully cool before using again. If it still fails to start contact your dealer
• If the Pressurised Tank Cap (5) is venting steam the steam cleaner tank has excessive
pressure, operate the steam trigger to reduce pressure. If the safety valve is venting
steam regularly in normal use it may indicate a fault with the unit or safety valve
Solution
switch on steam cleaner
refill tank with water
wait until heating indicator
turns off
refill tank with water
wait until heating indicator
turns off
refill tank with water
descale using a descaling
solution suitable for a
steam cleaner
rre-fit connector
clean connector
replace seal or accessory
part
only fill to a maximum
of 1200ml
place steam cleaner on a
level surface