Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
`
Part No.
22108X, TG53X
Do not over tighten as screws can be stripped out.
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
DO NOT OVER TORQUE. STANDARD OPERATING LOAD FOR TIGHTEN
BODY MOUNT NUTS & BOLTS VARIES FROM 45 TO 65 FOOT POUND.
Phillips Screw Driver (For Securing Screws in Scrivets)
1. INSTALLATION PROCEDURE:
Description
Under Rail Bedliner
Tailgate Cover
Installation Kit
2. Tailgate Cover Installation Steps with Screws
Page 1 of 7
DODGE DAKOTA UNDER RAIL
BEDLINER
Tools Required
Verify Kit Contents:
DODGE DAKOTA UNDER RAIL BEDLINER
Kit Contents:10 Scrivets,
Qty.
1
2 Tie Down Hole Plugs (Short Bed Only),
1
Installation Instruction Sheet
1
STEP 1 (FIGURE #2)
Center the Tailgate Cover on the Truck Tailgate. Press the
Cover Down and Forward into Place. Line up Holes in Tailgate
Cover with Holes in Truck Tailgate.
STEP 2 (FIGURE #3)
Place Scrivet Fastener in hole.
PRESS DOWN FIRMLY on the Scrivet Fastener to Seat in
Hole.
Repeat Procedure for the 7 Other Scrivet Fasteners.
STEP 3 (FIGURE #4)
Using Phillips Screwdriver, Tighten the 8 Scrivet Screws.
Do Not Over-Tighten.
DO NOT USE POWER TOOLS.
CUTTING NOT
30-60 min
REQUIRED
1 866 638 4870
Limited Lifetime
www.TrailFX.com
DRILLING
REQUIRED
Rev 062816
Manuales relacionados para Trailfx 22108X
Resumen de contenidos para Trailfx 22108X
- Página 1 DODGE DAKOTA UNDER RAIL BEDLINER Part No. 22108X, TG53X Do not over tighten as screws can be stripped out. CUTTING NOT DRILLING 30-60 min REQUIRED REQUIRED REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. [email protected] READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
- Página 2 3. Bedliner Installation CAUTION: It is Recommended that Two (2) People Install the Bedliner to Avoid Damage to the Painted Surface of the Truck. STEP 1 (FIGURE #5) Place Bedliner in the Truck Bed, such that, the Front Rail Retainer Fits Over the Front Rail of the Truck Bed.
- Página 3 DOUBLURE DE PLATEAU SANS REBORD POUR DODGE DAKOTA Part No. 22108X, TG53X Outils Nécessaires: Tournevis Cruciforme ((Pour attacher les vis dans les chevilles) 1. Préparation pour installation – Vérifiez le contenu du kit : DOUBLURE DE PLATEAU SANS REBORD POUR DODGE DAKOTA...
- Página 4 3. Installation de la doublure du plateau PRUDENCE: Il est conseillé à deux (2) personnes d’installer la doublure du plateau afin d’éviter des dégâts à la surface peinte du pick-up. ÉTAPE Nº1 (FIGURE Nº5) Installez la doublure sur le plateau du pick-up de sorte que le rebord avant recouvre la paroi avant du plateau du pick-up.
-
Página 5: Herramientas Necesarias
DEL FORRO BAJO LA BARANDA PARA DODGE DAKOTA Part No. 22108X, TG53X HERRAMIENTAS NECESARIAS: Destornillador Phillips (Para asegurar los tornillos en los tarugos) 1. Preparación para instalar - Verifique el contenido del juego: FORRO BAJO LA BARANDA PARA DODGE DAKOTA Contenido del juego: Descripción... - Página 6 3. Instalación del forro en la caja PRECAUCIÓN: Se recomienda que dos (2) personas instalen el forro para evitar daños a la pintura de la carrocería de la camioneta. PASO 1 (FIGURA #5) Coloque el forro en la caja de la camioneta, de modo que el retenedor de la baranda frontal quepa sobre la baranda frontal de la caja de la camioneta.
- Página 7 Product not installing properly. Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly. Check out these other TrailFX Products!! www.TrailFX.com Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of purchase by the original retail consumer.