Tabla de contenido
Idiomas disponibles
Idiomas disponibles
2506368_NoticeFreshmaxReib_Moulinex_Mise en page 1 25/11/13 17:02 Page6
1. APPLIANCE DESCRIPTION
A - Motor unit
B - On/off switch and speed selector
C - Pusher
D - Cone holder/feed tube
E - Cones
E1 - Coarse grating cone (red)
E2 - Fine grating cone (metal with
orange edge)
2. BEFORE USING FOR THE FIRST TIME
• Wash the accessories (cones, cone holder and pusher) with soapy water. Rinse and then dry ca-
refully.
WARNING: The cone blades are extremely sharp, handle the cones carefully always holding
them by the plastic part.
3. USE
• Choose the cone that corresponds to the required use.
• Position the cone holder (D) on the motor unit (A) by giving it a quarter turn to the left (fig.
1 & 2).
• Place the chosen cone into the opening at the front of the holder (D), the cone should be cor-
rectly positioned all the way into the drive (fig. 3).
• Plug in the appliance.
• Select the required speed (slow or turbo) and then press the start/stop button (fig. 4).
WARNING: before running the appliance, always make sure that the cone is perfectly
positioned on the motor rive unit (fig. 3) then first of all press the On/Off button before
inserting food into the feeder tube (fig. 4).
• Insert the food through the feeder tube (D) and push the food down gently using the pusher
(C) (fig. 5).
TIP: There is no need to press down hard on the pusher to obtain good slicing results; this
type of use will slow down the motor; simply ensure that the ingredient remains in contact
with the cone.
• To change the cone, turn the holder (D) a quarter turn to the right (fig. 6), then return it to
the upright position (fig. 7). Remove the cone (fig. 8).
6
E3 - Potato grating cone (yellow)
E4 - Thin slicing cone (metal with light
green edge)
E5a - Dicing cone (dark green)
E5b - Dicing ring (dark green/white)
F - Storage accessory
RECOMMENDATIONS FOR USE
The slow speed is also recommended for soft or fragile foods (pears, avocadoes, cooked beetroot).
Fitting the dicing accessory:
• Place the dicing cone in the opening at the front of the holder (D), the cone should be correctly
positioned all the way into the drive (fig. 3).
• Then position the dicing ring with the safety flap open, centring the safety hinge on the cone
holder tube (fig. 9).
• Check that the dicing ring is correctly attached to the base of the cone holder.
• Close the safety hinge over the cone holder (fig. 10).
• Use the dicing function by inserting the ingredients through the cone store feeder.
• Remove the dicing accessory by pulling the tab positioned at the top of the safety hinge
(fig. 11).
Tip: to unlock the safety hinge E5b more easily, move it upwards with one finger while
simultaneously pulling the tab forward (fig.11).
F.A.Q.
Questions
Simply make sure that the cone is slotted all the way
• "The Cone is not properly held in
place in the holder, I can't hear a
onto the drive (fig. 3). Press the on/off button first
click".
before inserting food into the feed tube to ensure the
cone is correctly locked into place (fig. 4).
• "I can't remove the accessory after
To remove the cone after use, unlock (fig. 6) the holder
use".
then relock it (fig. 7) and the cone will fall out by itself
(fig. 8).
• "The cone holder is quite hard to
Yes when the appliance is new. With use it will become
fit and remove, is this normal?"
easier to install and remove.
EN
Answers
7
Tabla de contenido
