AmerTac RFK106 Guia De Inicio Rapido

Wireless RF Remote Control System
Hand Held Transmitter and Plug-in Receiver
Imagine turning on your house lights from inside your car. Or turning off your stereo from across the room. This wireless Radio Frequency (RF) control now
makes it possible. RF Controls are an easy, convenient way to remotely control lights, and appliances in and around your home or office. The invisible RF signal
passes through walls, doors, ceilings, floors and even around corners. Simply plug the desired appliance into the receiver and the receiver into any outlet. A
press of the button on the hand held transmitter, turns whatever you've plugged into the receiver on or off.
Channel Code Information
Three operating channels are available so you can control three separate systems at different locations in your home. Be sure to match common frequency
channels, for those devices you want operated by the same switch.
INSTRUCTIONS
Notes: The total load of appliances connected to the Plug-in Receiver should not exceed 1200
Watts or 10 Amps.
Do not use Plug-in Receiver to control appliance loads that may be dangerous to turn on
remotely (i.e. power tools).
The Plug-in Receiver must be located within 100 feet of the Wall Transmitter.
A Remove back cover of Hand Held Transmitter by pushing cover down.
A Remove plastic battery tab by gently pulling it from the battery compartment (this tab isolates
the battery until it's ready for use and insures that you'll have a fresh battery).
A Reassemble Hand Held Transmitter.
A Plug your light/appliance into the outlet on the Receiver being careful to match the wide
blade of the light/appliance (if equipped) with the wide slot on the outlet.
A Plug the Receiver into any standard grounded 110/120 Volt outlet being careful to match the
wide blade of the Receiver with the wide slot on the outlet. Fully insert.
A Hold your Hand Held Transmitter at the location where you wish to use it.
A Press Switch to determine if your light/appliance turns on and off. If your light/appliance does
not respond try relocating the transmitter or receiver. Large metal objects such as metal doors
should not be in the way of the Transmitter and Plug-in Receiver since this could decrease the
range of the RF signal.
A Attach transmitter to any key ring or place in a convenient location around the house.
OPERATION
Simply press the button on the Hand Held Transmitter to turn the light/appliance you've plugged
into the Receiver on or off.
Note: Wait at least 3 seconds after you press the transmitter on or off before you press it again.
This allows for the RF signal transmission to be completed.
BATTERY REPLACEMENT
Your RFK106 battery should last 2-3 years under normal use.
To replace battery:
A Remove back cover of Hand Held Transmitter by pushing down
on back and sliding in direction of arrow.
A Remove battery from Battery Compartment and replace with
another 12Volt battery (Radio Shack™ 23, 23M, VR22, EL22 or
equivalent).
1 Year Limited Warranty
AmerTac™ warrants this product to be free from defects in material and workmanship for a
period of 1 year from the date of purchase. AmerTac's obligations are limited to repairing or
replacing any defective units and are effective only if such units are returned within 1 year of the
purchase date, to AmerTac, 250 Boulder Drive, Breinigsville, PA 18031. Warranty void if damage
is due to accident, negligence, misuse, alteration or improper installation. In no circumstance will
AmerTac be liable for consequential or incidental damages relating in any way to this product.
Questions, ¿Preguntas?, La question? 1-800-777-0802
©2009 AmerTac™
250 Boulder Drive
Breinigsville, PA 18031
www.amertac.com
Made in China / Hecho en China / Fabriqué en Chine
I09-0062-B
SPECIFICATIONS
240 Watts Tungsten Load, 120 Volts~, 60 Hz
Appliances up to 1200 Watts
10 Amps General Use Load, 120 Volts~, 60 Hz
Range 100 feet
Battery 12 Volt, Radio Shack™ 23, 23M, VR22, EL22
or equivalent
BACK
FCC Approved.
COVER
Plug-in receiver for indoor use only
Caution: Use of this product is licensed by the Federal
Communications Commission (FCC). Changes or
modifications not expressly approved by the party
BATTERY
responsible for compliance could void the user's
COMPARTMENT
authority to operate the equipment.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
• Connect the equipment into an outlet on a circuit
• Consult the dealer or an experienced radio/TV
RFK106, RFK106L
Troubleshooting Guide
SYMPTOM PROBABLE CAUSE
Light does not 1. Circuit breaker or fuse is turned
turn on. off.
2. Switch on lamp is turned off.
3. Bulb is defective.
4. Weak battery.
5. Lamp module or lamp is loose.
Light does not 1. Transmitter signals are being
turn off. blocked. Check for metal objects
that could block the signal, or
reposition the transmitter.
2. Switching too fast. Wait 3
seconds between toggles.
3. Weak battery.
Light comes 1. Short term power line failure.
on randomly. 2. Transmitter out of range.
3. Lamp module or lamp is loose.
the receiver.
different from that to which the receiver is connected.
technician for help.