Idiomas disponibles
Idiomas disponibles
STEP 1
1 – Fit the NN slides in the parts 4 and 10. Use a rubber mallet
to help fitting the part.
2 – Fasten de M Hinges Wedges on the part 10 with (4x12mm)
NN
4
X screws.
M
2
X
4
4
STEP 2
1 - Fasten de M Hinges Wedges on the part 1 with (4x12mm)
X screws.
M
4
X
8
1
STEP 3
1 – Insert (6x30mm) A Pegs in the parts 2, 3, 4, 5, 6, 7, 8, and 9.
A
32
9
8
7
6
5
4
3
2
All manuals and user guides at all-guides.com
STEP 4
1 – Fit part the PART 2 to the part 1 and fasten them with
(3.5x40mm) PH screws.
PH
2
STEP 5
1 - Fit the part 3 to the part 4.
10
STEP 6
1 – Fit the part 3 to the part 1, and the part 4 in the part 2.
STEP 7
1 – Fit the part 5 to the parts 1 and 4.
2 – Fit the parts 6, 7, 8 and 9 in the part 1.
3 – Fasten the parts 5, 6, 7 and 9 in the part 1 with (3.5x40mm)
PH
8
PH screws.
STEP 8
1 – Fit the part 10 to the parts 2, 5, 6, 7, 8 and 9.
2 – Fasten the part 10 in the parts 2, 5, 6, 7 and 9 with
(3.5x40mm) PH screws.
PH
10
2
STEP 9
1 – Place the PE legs on the base 2 holes and fasten them
with (4x35mm) PF screws.
PF
4
PE
4
1 – ATTENTION: Before fastening the bottoms check the cabinet
STEP 10
square.
2 – Align one part 17 to the sides and to the top of the cabinet.
Fasten it with D nails.
D
70
3 – Then align the parts 17 and 14, and fasten them to the sides
with D nails.
4 - Align the parts 15 and 16, and fasten them to the sides and
on the base with D nails.
5 – Use D nails plus E fasteners on the junctions between the
bottoms.
E
12
17
14
STEP 11
1
2
STEP 12
3
4
STEP 13
1
3
4
2
STEP 14
9
1
8
7
5
6
4
STEP 15
9
8
7
6
5
10
2
15
16
1 - Fit the hinges M on the doors and fasten them with
(4x12mm) X screws.
X
12
M
6
1 – Place the S handles on the doors holes and fasten them
with (3.5x25mm) W screws.
W
6
12
12
S
3
11
1 - To fit the door, fit the M hinges to the M wedges by locking
it to the screw indicated with # 1 below.
6
M
M
6
To adjust the doors, follow the instructions below:
1. If you need to raise or lower the door a little, loosen the screws
indicated with # 1, reposition and tighten again.
2. If you need to push the door a little further in or pull it out,
loosen the screw indicated with # 2, reposition it and tighten
again.
3. If you need to align the doors a little further towards the
center or toward the sides, use a Philips screwdriver to rotate
the screw indicated with # 3 until you position the door
the way you want.
1 – Fit the FF baskets on the plastic slides fastened on the
sides and partition.
2
FF
1
1
2
3
