Hoffman Berkel PROXIMA 800 Manual Del Usuario página 10

Remove product holder plate:
- with the regulating knob for
slice thickness (3) in the safe-
ty position (Fig. A, Fig. D-1),
pull back the carriage (5) all
the way until the travel limit
toward the operator (Fig. D-2);
- loosen the knurled knob of
the product holder plate (18)
(Fig. E);
- push the product holder plate
slightly downwards (Fig. F)
- take off the product holder
plate (17).
Tilt the carriage aside
- loosen the plate locking knob
(7) of the carriage
- pull back the carriage (6) to-
ward the operator;
- tilt the carriage aside.
WARNING! Do not tilt
!
the carriage aside in
case the thickness plate is still
opened. Always tilt the carriage
with care, do not use force!
WARNING! Keep the reg-
!
ulating knob for slice thick-
ness in the safety position "0".
Removing the blade cover
(Fig. H)
- rotating in the anticlockwise
direction, loosen the blade cov-
er tension rod grip (13);
- press the tension rod grip and
raise the blade cover to remove it.
WARNING! Once the
!
blade cover has been re-
moved, an interlocking device
stops the blade rotation.
Removing the slice deflector
(Fig. I)
Pull the deflector upwards and
take It off to the front.
Cleaning:
- the blade: press a damp cloth
on the surface of the blade and
move it slowly from the center
toward the outside on the
blade cover side and the oppo-
site side. In the same way dry it
using a dry cloth. NEVER turn
on the machine while cleaning
the blade;
- the safety ring: use a soft
brush to clean the area be-
tween the blade and the safe-
ty ring. Be careful NOT to put
your hands close to the blade;
- the machine body: use a damp
cloth or a sponge. Dry carefully;
- the sharpener: 1) clean the
body with a damp cloth and the
springs with a semi-rigid brush.
2) do not submerge the sharp-
ener in water. The sharpening
wheel can easily be removed
from the sharpening unit, re-
moving it in the direction of the
arrow (Fig. G). Keep the wheel
clean for correct sharpening.
Remove dirt and grease with
alcohol and a semi-rigid nylon
brush.
MAINTENANCE
Blade Sharpening
Frequency and duration of
sharpening depend on the use
of the equipment.
WARNING! Every sharp-
!
ening device is marked
with the serial number of the
machine: use only the "27
SHARPENING DEVICE".
Usage of another sharpening
devices can cause serious in-
juries or damage the machine.
Never use another sharpening
device. The sharpening de-
vice is equipped with two fine
sharpening stones, one is for
sharpening and one is for tak-
ing off the burr.
Before sharpening:
1. make sure that the machine
8
is off;
2. position the thickness ad-
justment knob in the safety
position;
3. open the thickness gauge
plate completely;
4. position the carriage in the
centre;
5. lift up the product holder;
6. mount the sharpening device
in such a way to the thickness
plate that mount the sharpen-
ing device in such a way to the
thickness plate that the cone of
the sharpening device fits into
the slit on the bottom of the
thickness plate (direction of
arrow) (L);
7. pull out the pin on top of the
sharpening device in direction
of arrow and move the sharp-
ening device over the edge of
the thickness plate (M);
8. move the sharpening device
with the pulled out pin to the
front in direction of the blade
(direction of arrow), so that the
pin is engaged in the hole of the
thickness plate (N);
9. the sharpening stones are
now in the correct position,
the blade edge is positioned
between the two sharpening
stones;
10. switch on the machine;
11. turn the yellow handwheel
of the sharpening device in di-
rection 1 for about 15 seconds
(Fig. P);
12. switch off the machine;
13. for taking the burr off, turn
the yellow handwheel in direc-
tion 2 for about 2 seconds;
14. turn the yellow handwheel
to 0;
Remove the sharpening device
1. switch off the machine;
2. pull the pin of the sharpening
device upright;
3. tilt the sharpening device
aside to the right;