Uline H-5333 Guia Del Usuario
Ocultar thumbs Ver también para H-5333:
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

H-5333
AUTOMATIC PAPER
CRUMPLER – FLOOR STANDING
TOOLS INCLUDED
1/8"
7/32"
Allen Wrench
1.
Remove all parts from the three shipping cartons.
2. Position floor base on a flat surface.
3. Lock all casters by stepping down on black plastic
locks to secure the base during assembly.
(See Figure 1)
4. Position tubular center bar so the single hole is at
the top of the beam and facing the short side of the
floor base. (See Figure 1)
5. Line up two holes at the bottom of the tubular center
bar with the holes in the middle of the floor base.
Secure with 3/8-16 x 5" bolts, 3/8 lock washers, and
3/8-16 nuts (2 each). (See Figure 1)
Figure 1
Tubular
Center Bar
Floor Base
Locked
PAGE 1 OF 13
1-800-295-5510
uline.com
1/4"
5/16"
ASSEMBLY
TOOL NEEDED
9/16" Wrench
6. From back of unit, line up the two tubular stabilizer
bars to the back cross sections of the floor base. The
welded nuts at the top should be facing the short
side of the base. (See Figure 2)
7.
Secure the two tubular stabilizer bars to the floor
base using 3/8-16 x 3.5" bolts, 3/8 lock washers, and
3/8-16 nuts (4 each). (See Figure 2)
NOTE: Lay floor base on its side. Start with the
bottom bolt. Bolts should be inserted from the
back of the unit and secured between the two
cross sections of the floor base.
Figure 2
Para Español, vea páginas 5-9.
Pour le français, consulter les pages 10-13.
Tubular
Stabilizer Bars
0621 IH-5333
Tabla de contenido
loading

Resumen de contenidos para Uline H-5333

  • Página 5: Plegadora De Papel Automática - De Piso

    H-5333 800-295-5510 uline.mx PLEGADORA DE PAPEL AUTOMÁTICA – DE PISO HERRAMIENTA HERRAMIENTAS INCLUIDAS NECESARIA 1/8" 7/32" 1/4" 5/16" Llave de 9/16" Llave Allen ENSAMBLE Saque todas las partes de las tres cajas. 6. Desde la parte posterior de la unidad, alinee los dos tubos estabilizadores con las secciones 2.
  • Página 6: Continuación De Ensamble

    CONTINUACIÓN DE ENSAMBLE 8. Deje a un lado la base. 12. Deslice el inserto central y los insertos estabilizadores en la barra con centro tubular y en el tubo central 9. Localice el cuerpo de la máquina con la cuneta para y los tubos estabilizadores en la base ensamblada papel.
  • Página 7: Funcionamiento

    CONTINUACIÓN DE ENSAMBLE 15. Coloque la rampa de papel en el embudo de 16. Inserte la conexión azul Diagrama 8 entrada y fíjela con seis pernos de 10-32 x 1/2", del motor en el enchufe asegurándose de que las cabezas de los pernos azul ubicado en la parte queden dentro del embudo.
  • Página 8: Solución De Problemas

    SOLUCIÓN DE PROBLEMAS PROBLEMA DE FUNCIONAMIENTO CAUSA RECOMENDACIONES La máquina no recibe electricidad. La unidad no está enchufada. Enchufe el cablee eléctrico a un tomacorrientes estándar de 115V. El motor no está conectado a Conecte el enchufe azul del motor la caja del interruptor.
  • Página 9: Continuación De Solución De Problemas

    Repita hasta que las ruedas motrices ya no rasguen el papel. Si los problemas persisten, llame a Servicio a Clientes de Uline al 800-295-5510. 800-295-5510 PAGE 9 OF 13 0621 IH-5333...

Tabla de contenido