koban KT11-LCD-P Manual De Instrucciones página 4

OUT 8AM 61/16 8AM 61/16
6PM 70/21 6PM 70/21
BACK
10PM 61/16 11PM 61/16
SLEEP
Cool Mode:
Time
MON~FRI SAT
Zone
time °F/°C time °F/°C
WAKE 6AM 75/24 6AM 75/24
OUT 8AM 85/29.5 8AM 85/29.5
6PM 75/24 6PM 75/24
BACK
SLEEP 10PM 85/29.5 11PM 85/29.5
Program Setting
The above program time and temperature can be modified.
To adjust Heat/Cool program settings:
1. Select Heat/Cool mode by pressing MODE button at Normal Display
Mode.
2. Press SET button to enter Setting Menu.
3. Press NEXT button to display PROG.
4. Press ENT button to enter program setting: "ON"/"OFF".
5. Press UP or DOWN button to select program on / program off.
6. Make sure "On" is selected, press NEXT button to select the item that
you want to change (Weekday/Weekend, Four Zones, Hour, Minute or
Setting Temperature).
7. Press UP or DOWN button to adjust the item.
8. Press MODE button to return to Weekday/Weekend program
9. Press MODE button again, to confirm the setting and return to Setting
Menu.
10. Press NEXT button to return to Normal Display Mode or the operation
will return to Normal Display Mode if no key is pressed for 10 sec.
Temporary Override
When Program is On, this thermostat controls the output according to the
program.
If you want to override the programmed temperature temporarily:
1. Press UP or DOWN button to adjust Heat/Cool setting temperature
setpoint with displayed.
2. The Heat/Cool setting temperature will be confirmed and return to
Normal Display Mode if no key is pressed for 10 sec.
Temporary Override Mode will last until the next programmed time zone)
begins. At that time, the Heat/Cool setting temperature will follow the
programmed setting temperature and
can be stopped manually by pressing MODE key.
Program Off
When Program is Off, this thermostat controls the output according to a
single setpoint like a simple setback thermostat. To set the unit to be
Program Off, follow the above "Program Setting" to select Program Off.
When this thermostat is Program Off, the Program Mode will be disabled
and the time zone icons will disappear in Normal Display Mode.
To adjust the setpoint at Program Off:
1. Press UP or DOWN button to adjust the Heat/Cool setting temperature.
8AM 61/16
6PM 70/21 The icon
2. The Heat/Cool setting temperature will be confirmed and return to Normal
11PM 61/16
Display Mode if no key is pressed for 10 sec.
Fan Operation
SUN
If FAN ON is selected, fan runs continuously.
time °F/°C
If FAN AUTO is selected, fan runs only when the Heating/Cooling system is
6AM 75/24
on. Fan will be turned off 2 minutes after the Heating system is off.
8AM 85/29.5
6PM 75/24
Fan Mode setting:
11PM 85/29.5
1. Press SET button to enter Setting Menu.
2. Press NEXT button to display FAN and press ENT button.
3. Press UP or DOWN button to select FAN ON / FAN AUTO.
4. Press MODE button to confirm the setting and return to Setting Menu.
5. Press NEXT button to resume to Normal display mode or the operation
will return to Normal Display Mode if no key is pressed for 10 sec.
Advanced Setting
Advanced Setting contains Function Setting Selection, Temperature Calibration
and Room Temperature Display.
Function Setting Selection
Function
Type
1. Press and hold SET and DOWN buttons for 2 seconds to enter Advanced
Setting Mode.
2. The left letters represent Function Type; the right letters represent the
settings.
3. Press UP or DOWN button to adjust the setting.
4. Press NEXT button to select Function Type or to return to Normal Display
Mode at the end of Function Setting selection or the operation will return to
Normal Display Mode if no key is pressed for 10 sec.
Table of the Function Setting Selection:
Function Type
will disappear. Or
Description
12hr/24hr
Selection
Temperature
Display Unit
Temperature
Control Span
Fan Control
will NOT be shown in Program Off.
Setting
<Up> Key
<Down> Key
<NEXT> Key
LCD Setting
Display
12
hr
24 (default)
°C (default)
dE
°F
05 (+/- 0.5C ) (default)
10 (+/- 1.0C )
SP
10 (+/- 1F)
20 (+/- 2F)
E (Electrical Heat) (default)
FC
O (Gas/Oil Heat)
Heater S (10 seconds) (default)
Minimum-Off dL
L (4 minutes off time)
Delay
0 (Disable) (default)
Heat Pump HP C (O/B terminal energized in cooling)
H (O/B terminal energized in heating)
Temperature Control Span controls how much the room temperature
can be deviated from the setpoint. A smaller degree will result in a more
accurate control. A larger degree will result in less on/off cycling and it
usually saves more energy.
Fan Control should be set according to the type of Heating system used.
Select "E" for Electric Heat, fan will be On when Heat is On. Select "O"
for Gas Heating or Oil Heating, fan will NOT be on when Heat is On.
Heater Minimum Off Delay should be set according to the heater type.
Select "L" if compressor is used for heating. Select "S" when a
compressor is not used.
Heat Pump should be set according to air conditioning system. Select
"0" if heat pump is not used. If heat pump is used, select "C" if it uses
electric energy to move the cool or select "H" if it uses electric energy to
move the heat.
Temperature Calibration
This thermostat is calibrated at factory and calibration is generally not
required. However, in the event that a deviation is found,
1. In Normal Display Mode, press and hold UP and DOWN buttons for
5 seconds to change the temperature calibration display and the
current temperature will flash,
2. Press UP and DOWN button to calibrate the temperature. The
maximum range to be adjusted is +/- 3.0°C or +/- 6°F, in step of
0.5°C / 1°F.
3. Press MODE button to confirm the setting and return to Normal
Display Mode or the operation will return to Normal Display Mode if
no key is pressed for 10 sec.
Specification
1. Temperature Measurement: 0 - 40C / 32 - 99F
2. Accuracy: ±0.5C / 1°F
3. Resolution: 0.5C /1°F
4. Power Supply: 2 x AAA Alkaline Batteries
5. Relay Contact Voltage: 24Vac ~ 230Vac Max. 50/60 Hz
6. Relay Contact Current: 5(3) A Max. (Inductive)
7. Sensing Element: NTC Thermistor
8. Heat/Cool Setting: 5 - 35C / 40 - 95F
9. Operating Temperature: 0 - 50°C / 32 - 122°F
Storage Temperature: -5 - 5
10. 0°C / 23 -122°F
TEMPER ENERGY INTERNATIONAL S.L.
Polígono industrial de Granda, nave 18
33199 • Granda - Siero • Asturias
Teléfono: (+34) 902 201 292
Fax: (+34) 902 201 303
Email: [email protected]
www.grupotemper.com
141104