Cub Cadet XT1 LT42E Manual De Operación página 14

Your tractor should be cleaned after each use and under certain conditions, i.e. dry
conditions and/or mulching situations, additional cleaning may be necessary.
One of the best ways to keep your tractor running efficiently and to reduce fire risk
is to regularly remove debris buildup from the tractor. Follow the recommendations
below and contact your authorized dealer with any questions.
• Allow the tractor to
cool in an open area
before cleaning.
• Do not use water
on any part of the
tractor. Doing so can
cause damage to the
tractor's electrical
components and
motors. The use of
compressed air and/or
leaf blower or a brush,
damp sponge or
rag will help keep
the tractor clean.
• Clean around
fuses and wiring
harnesses.
• Clean the top of the
tractor deck. See
Figure 17.
• Clean around
and near the
transmission and
axle. See Figure 18.
• Debris can accumulate anywhere on the tractor, especially on horizontal
surfaces. Additional cleaning may be necessary when mowing in dry
conditions or when mulching.
• Excess lubrication can become collection sites for debris. Immediate repair
and cleaning up excess lubrication can help reduce fire hazards.
• In addition to cleaning the tractor before operating and storing, do not
attempt to mow unusually tall grass (10" (25.4 cm) or higher), dry grass (e.g.,
pasture) or piles of dry leaves. Dry grass or leaves may build up on the tractor
deck presenting a potential fire hazard.
Lubrication
Bearing failures and overheating can result in fire. Always follow the
instructions in this manual regarding lubrication locations and intervals.
Contact your authorized dealer with any questions about the lubrication
locations and intervals or any unusual noises coming from any areas a
bearing may be located.
Before lubricating, repairing, or inspecting, always disengage the PTO, set
the parking brake, and remove key to prevent unintended starting.
Front Wheels
Each of the front wheel axles and rims is equipped with a grease fitting. See Figure
19 for the location of the grease fitting on the axles and Figure 20 for the location of
the grease fitting on the rims. Lubricate with a No. 2 multi-purpose grease applied
with a grease gun after every 25 hours of operation.
SERVICE AND MAINTENANCE
Figure 17
Rear Wheel Not
Shown For Clarity
Figure 18
DANGER
WARNING
Figure 19
Deck Wheels
The wheels on the deck which are spherical in shape are equipped with a grease
fitting. Lubricate with a No. 2 multi-purpose grease applied with a grease gun after
every 25 hours of operation.
Pivot Points & Linkage
Lubricate all the pivot points on the drive system, parking brake and lift linkage
every 10 hours with light oil.
NOTE: It is not necessary to grease the steering pinion/sector gear interface. Doing
so will allow dirt to accumulate and can affect steering performance.
Adjustments
Before making adjustments, always disengage the PTO, set the parking
brake, turn key to OFF position and remove to prevent unintended starting.
Protect your hands by using heavy gloves when handling the blades.
NOTE: Check the tractor's tire pressure before performing any deck leveling
adjustments. Refer to Checking Tire Pressure in the Assembly section for
information regarding tire pressure.
Adjusting the Deck
Leveling the Deck (Front-To-Rear)
The front of the deck is supported
by a stabilizer bar that can be
adjusted to level the deck from
front to rear. The front of the deck
should be between 1⁄4" (6.4 mm)
and 3⁄8" (9.5 mm) lower than
the rear of the deck. Adjust if
necessary as follows:
1. Park the tractor on a firm,
level surface, place the
deck lift lever in the middle
position and rotate the
blade nearest the discharge
chute so that it is parallel
with the tractor.
2. Measure the distance from the front of the blade tip to the ground and the
rear of the blade tip to the ground. The front of the blade should be between
1⁄4" (6.4 mm) and 3⁄8" (9.5 mm) less than the rear of blade.
3. Determine the approximate distance necessary for proper adjustment and
proceed, if necessary.
To raise the front of the deck, loosen the outer nut then tighten (thread
4.
inward) the nut against the front hanger bracket. See Figure 21. When
proper adjustment is achieved, re-tighten the outer nut to 25-30 ft-lbs
(33.9-40.7 N-m).
To lower the front of the deck, loosen the outer nut then loosen (thread
5.
outward) the nut, away from the front hanger bracket. See Figure 21. When
proper adjustment is achieved, re-tighten the outer nut.
14
Figure 20
WARNING
Figure 21