General Safety Information; General Safety Instructions; Installation Instructions - Speedaire 4ZL84A Instrucciones De Funcionamiento Y Manual De Piezas

GENERAL SAFETY INFORMATION

Speedaire MIST air line lubricators are designed to deliver an atomized
oil mist to the compressed air which drives an air-powered tool and/or
air motor, etc, and lubricates the interior moving part(s) of the tool and/
or motor, extending the tool/motor life. These lubricators are equipped
with a sight-feed dome, a green drip rate adjustment, and a flow sensor.
The sight-feed dome provides visual indication of oil drop rate. The
green drip rate adjustment regulates oil drop rate. The flow sensor
compensates for changes of air flow demands.
The device may only be operated in the permanent installation in
pressured air systems. Improper use or modifications to the device or
the use of its components which are not tested and approved by the
manufacturer may result in unforeseen damage.
Speedaire MIST lubricators are used in a variety of air systems which
may go with air compressor, filters, regulators, hoses, etc. Read and
understand all safety instructions, installation instructions and operation
instructions before using this unit. Basic safety precautions should
always be followed to reduce the risk of personal injury and/or property
damage.

General Safety inStrUctionS

1. Read all safety instructions. Failure to do so may cause harm to you
and others.
2. Keep children and unauthorized persons away from the device.
Ensure that children are not able to play with the device.
3. Do not overload the device. Do not use the device for purposes for
which it is not intended.
4. Always make sure that the air line is in good condition.
5. Hose and connection should be inspected to avoid any leakage
before use.
6. Residual air in the system needs to be released before service or
repair.
7. Ensure that all connections and supply lines are rated for the required
pressure and air flows.
CAUTION
Polycarbonate bowls are not recommended for
use in atmospheres containing chemicals such
as acetone, benzene, carbon tetrachloride, gasoline, toluene and/or air
compressor systems using synthetic fire-resistant lubricants.
2
SPECIFICATIONS
Max. Inlet
Model Max. temp. Max. Flow
Press.
4ZL84A 250 psi 175°F 114 cfm
4ZL85A 150 psi 125°F 114 cfm
4ZL86A 250 psi 175°F 154 cfm
4ZL87A 150 psi 125°F 154 cfm
4ZL88A 250 psi 175°F 142 cfm
4ZL89A 150 psi 125°F 142 cfm
• Air supply must be dry enough to avoid ice formation below +35°F.
• At 150 psi inlet pressure, set pressure of 90 psi, and a 15 psi pressure drop.
DIMENSIONS (inch)
Grainger Items No. Length (In./mm)
4ZL84A 3.15/80
4ZL85A 3.15/80
4ZL86A 3.15/80
4ZL87A 3.15/80
4ZL88A 3.15/80
4ZL89A 3.15/80
NOTE:
Polycarbonate bowls are not recommended for use in atmospheres containing
chemicals such as acetone, benzene, carbon tetrachloride, ethylene dichloride,
gasoline and/or air compressor systems using synthetic fire-resistant lubricants.

INSTALLATION INSTRUCTIONS

1. Before installation, check whether the connections used match the maximum pressure of the
lubricator.
2. Shut off air pressure from air system. Install the lubricator vertically with the bowl down in the
air line. Ensure that the lubricator is installed with inlet/outlet air flow in the proper direction of
arrow on the unit. The lubricator should be installed downstream of filter(s), regulator(s), and
cycling valve(s) in the air line, and should be as close as possible to the device being lubricated
(usually not more than 15 feet from the device). It is still essential that the lubricator should be
installed at the same height or higher than the device being serviced.
Main Ports Bowl Wt. (lbs)
3/8" Metal 1.70
3/8" Polycarbonate 1.70
1/2" Metal 1.61
1/2" Polycarbonate 1.61
3/4" Metal 1.55
3/4" Polycarbonate 1.55
Width (In./mm) Height (In./mm)
2.89/74 8.81/224
2.89/74 8.81/224
2.89/74 8.81/224
2.89/74 8.81/224
2.89/74 8.81/224
2.89/74 8.81/224
3