Tabla de contenido
Idiomas disponibles
Idiomas disponibles
479727-01,11684 sander
and 3-pole receptacles that accept the
tool's plug.
e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a
cord suitable for outdoor use reduces
the risk of electric shock. When using
an extension cord, be sure to use one
heavy enough to carry the current your
product will draw. An undersized cord
will cause a drop in line voltage
resulting in loss of power and
overheating. The following table shows
the correct size to use depending on
cord length and nameplate ampere
rating. If in doubt, use the next heavier
gage. The smaller the gage number,
the heavier the cord.
Minimum Gage for Extension Cords (AWG)
120 VAC Tools
Total Cord Length 0-25 26-50 51-100 105-150
Amp Rating AWG AWG AWG
More than 0
18
Not More than 6
More than 6
18
Not More than 10
More than 10
16
Not more than 12
More than 12
14
Not more than 16
3) PERSONAL SAFETY
a) Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired or
under the influence of drugs,
alcohol or medication. A moment of
inattention while operating power tool
may result in serious personal injury.
b) Use safety equipment. Always wear
eye protection. Safety equipment
such as dust mask, non-skid safety
shoes, hard hat, or hearing protection
used for appropriate conditions will
reduce personal injuries.
c) Avoid accidental starting. Ensure
the switch is in the off-position
before plugging in. Carrying power
tools with your finger on the switch or
plugging in power tools that have the
switch on invites accidents.
d) Remove any adjusting key or
wrench before turning the power
tool on. A wrench or a key left
attached to a rotating part of the power
tool may result in personal injury.
7/15/05
7:40 AM
Page 3
e) Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from
moving parts. Loose clothes, jewelry
or long hair can be caught in moving
parts. Air vents often cover moving
parts and should also be avoided.
g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of these devices can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
AWG
rate for which it was designed.
16
16
14
b) Do not use the power tool if the
switch does not turn it on and off.
16
14
12
Any power tool that cannot be
controlled with the switch is dangerous
16
14
12
and must be repaired.
c) Disconnect the plug from the power
12
Not
source and/or the battery pack from
Recommended
the power tool before making any
adjustments, changing accessories,
or storing power tools. Such
preventive safety measures reduce
the risk of starting the power tool
accidentally.
d) Store idle power tools out of the
reach of children and do not allow
persons unfamiliar with the power
tool or these instructions to operate
the power tool. Power tools are
dangerous in the hands of untrained
users.
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tools operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
g) Use the power tool, accessories
and tool bits etc., in accordance
with these instructions and in the
manner intended for the particular
3
Tabla de contenido
