Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

ELECTRIC DROPBOLT
I. Function:
This kind of lock is fail-safe, and operates with DC12V. 4 working grades of time delaying
circuit for using. You can choose any time delay to avoid the bolt throw out before the door
closing. There are circuits for door and bolt sensor in the lock, which guiding out for sensoring
of the lock and the working status (chart 1).
II. Instruction:
a) Please read this instruction carefully before using it, and check the accesories enought or
not. Please make a test according to the circuit connection before installing.
b) The lock were combined by two parts: (1) stainless steel sticker (2) body. The gap between
the sticker and the front of lock should be less than 3mm, and the hole of the sticker must
right to the bolt. The magnet must be set in the middle of the sticker.
c) 8 lines in the rear of the lock for connection, such as red, black, blue, white, yellow, green
gray and orange (chart 1), red for power (+), connecting DC12V or power DC12V under
controled, black for power (-) (chart 3), blue white yellow for bolt sensor, blue for NO, white
for COM, yellow for NC (chart 2A). The NC will be cut off it the bolt throw out. And, terminal
of No goes through green, gray and orange for door sensor, check the door status is open or
close, green for NO, gray for COM, orange for NC (chart 2B), the state of NO and NC.
d) Circuit connection (chart 3) the power for the lock must reach to DC12V
magnet
hole
bolt
(chart 1)
white (COM)
bolt sensor
yellow (NC)
blue (NO)
(chart 2A)
controlling machine
or access control
switch
220V/50Hz
+12V
red
Regulated
power
electric lock
(-)
black
(chart 3)
V11
Stainless steel sticker
(8 color guiding lines: red, black, blue, white
yellow, green, gray and orange)
gray (COM)
door sensor
orange (NC)
green (NO)
(chart 2B)
jumper adjuster
sensoring wires
0s
3s
6s
9s
(chart 4)
ELECTRIC DROPBOLT
e) The adjusting jumper for the time delay autolocks sets in the middle of the lock (chart 4) and,
the adjusting jumper can change the time for locking, 0s, 3s, 6s 9 optional
f) Installation (chart 5)
stainless
steel sticker
III. Specification:
Voltage: DC12V , 0.8Amp (with reverse polarity protection)
Red: positive (+)
Black: negative (-)
Current: start 0.8A, standby 0.09A
Solenoid: continuous duty
Fail-safe: all model
Auto relock jumper: adjustable (0-9s)
Function: fail-safe
Bolt: Dia. 15.5mm stainless steel out throw 15mm
Cutout: 212mmL x 35mmW (43mm bracket minimum must be present)
Bracket: 90mmL x 24mmW x 33mmD
Accesory: extending bracket (2pcs)
stainless steel sticker (1pcs)
installing bracket (1pcs)
M5 x 15mmL screw (5pcs)
M4 x 11mmL screw (8pcs)
M4 x 25mmL screw (3pcs)
Weight: 0.9Kg
IV. Note:
1) Please keep it away from moist place and water when install or use electric lock
2) The voltage of power supply should be between DC 12V and DC 12.8V.
V11
Extending iron
bracket
(chart 5)
loading

Resumen de contenidos para Dorcas V11

  • Página 1 ELECTRIC DROPBOLT ELECTRIC DROPBOLT I. Function: e) The adjusting jumper for the time delay autolocks sets in the middle of the lock (chart 4) and, This kind of lock is fail-safe, and operates with DC12V. 4 working grades of time delaying the adjusting jumper can change the time for locking, 0s, 3s, 6s 9 optional circuit for using.
  • Página 2 ELECTROPISTÓN ELECTROPISTÓN (Figura 1) I. Función: Controladora o control de accesos El funcionamiento de este electropistón es de tipo invertido y funciona con corriente continua a Interruptor 12V con la posibilidad de emplear 4 opciones de retraso en la función de bloqueo para evitar que 220V/50Hz Jumper ajustable +12V...