PALSON Dakar Modo De Empleo página 5

GB
Our products are developed to achieve the highest standards of quality, functionality and design. We hope you enjoy your new DAKAR
ceramic hair trimmer from PALSON.
Instructions for use
- Read the instructions carefully before using this unit.
- After reading them please make sure to keep them at hand for later reference by the user.
- This device should not be used by people (including children) whose physical, sensorial, or mental abilities are reduced or they lack
either experience or knowledge, unless they are being supervised or have had prior instruction as regards the use of the device by a
person responsible of its safety. Children should be supervised so as to make sure they do not play with the device.
- If the power cable is damaged, it should be replaced by the manufacturer or the authorized technical service centre or by a duly
authorized qualified technician to avoid risk.
Warning:
Make sure to apply lubricating oil on the blade before and after using the hair trimmer.
- If not, the blade may pull the hair, and consequently the blade may deteriorate.
- Please use the oil from the package or use the adequate and appropriate oil.
- The oil in the package should only be used on the blade; it is not appropriate for other uses.
- Do not charge or use the unit at a temperature lower than 0 ºC or higher than 40 ºC.
-
Do not charge the battery under direct solar light or near a radiant heat source.
- Do not charge, use, or store the device in a cold and damp place, or in a place with high temperatures.
- Do not charge the hair trimmer unless someone is present.
- WARNING: Keep the device dry.
How to charge the device
1. Place the switch on the main unit in position "O" (off).
2. Plug it in.
3. The lighted indicator will turn red when it is plugged in.
4. The battery will be completely charged after 8 hours of charging, and the full charge lighted indicator will turn on.
5. The hair trimmer may be used 1 hour after it is fully recharged.
6. Once the battery is charged, unplug the main unit.
7. Place the switch in position "I" (on) to use the device.
8. Place the switch in position "O" (off) after cutting your hair.
With the cable unit
1. Place the switch in position "O" (off).
2. Plug the main unit's plug into the outlet.
3. Once connected, the lighted indicator will turn red.
4. Place the switch in position "I" (on) to use the machine, then another lighted indicator will turn on.
5. Place the switch in position "O" (off) after cutting your hair, and then unplug the unit's cable from the plug.
When using the 4-size comb (10, 20, 30 and 40 mm) (Fig. 1)
1. With the switch in position "O" adjust the accessory to the height you wish by sliding it until it clicks in one of the 4 heights (Fig. 3).
2. Cut the hair at the height you wish by moving the hair trimmer towards the back in the hair direction. (The hair's actual length will be
a little bit longer than the selected height) (Fig. 4).
(Do not use the hair trimmer in an inverted position. This may cause the hair to be cut with too much depth) (Fig. 5).
3. Turn off the hair trimmer before changing the cutting height or before removing the accessory.
3 and 6 mm accessory combs.
1. To place the accessory comb in the hair trimmer, place the hook on one side of the accessory comb in the support, and then slide the
other side to the other support in the direction indicated with the arrow. (Fig. 7).
2. To remove the accessory comb from the hair trimmer, slide one side of the accessory from the support in the direction indicated by
the arrow (Fig. 8).
Accessory for short hair
1. For short hair (1/3 of hair), install the accessory for short hair on top of the hair trimmer's blades in the direction of the arrow (Fig. 9).
(Push until you hear a click).
2. To remove the accessory, push both sides in the directions of the arrow while you remove the accessory (Fig. 10).
8
Cutting without accessories
Cut the hair placing the hair trimmer's head directly on the scalp (Fig. 11). Cutting without accessories will leave the hair length at one
millimetre or less.
Blade assembly and disassembly
1. Hold the hair trimmer's body with the PALSON symbol upwards and push the blade in the direction indicated by the arrow with your
thumb.
At the same time, hold the blade with the other hand. Make sure the switch is in position "O" before removing the blade (Fig. 12).
2. To re-assemble the blade, fit the supporting hook in the blade mount on the hair trimmer's body and push it until it clicks (Fig. 13).
Duration of the blade and the battery
The blade's lifetime will vary according to the frequency and length of use. The blades' life expectancy is about 6 years if the hair trimmer
is used twice a month for 20 minutes each time. If the efficiency of the cut is substantially reduced despite appropriate maintenance, this
means that the blades have exceeded their useful life and need to be changed.
The battery's life expectancy will vary according to the frequency and length of use. If the battery is charged 3 times a month, its useful
life will be approximately 6 years. If the unit is not charged for more than six months, the battery will lose charge and its useful life may
be reduced.
Therefore, it is recommended to recharge the unit at least every six months, even if it is not used regularly.
Blade Care
Please clean the blade after use to protect it appropriately.
1. Place the switch in position "O" (off) and unplug it.
2. Remove the blade.
3. Take the blade from the hair trimmer and remove the upper part of the blade from the set. (Fig. 2)
4. Please be careful with the blade since it may cut you.
5. Use the cleaning brush to clean the blade and the unit (Fig. 14 and 15).
6. Add oil in the parts marked with an arrow point (Fig. 16).
7. Place the blade in the unit.
Thank you for trusting us by choosing one of our products.
9