LEGRAND Wiremold OFR Serie Instrucciones De Instalación
LEGRAND Wiremold OFR Serie Instrucciones De Instalación

LEGRAND Wiremold OFR Serie Instrucciones De Instalación

Ocultar thumbs Ver también para Wiremold OFR Serie:
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

OFR Series
Overfloor Raceway Transition Fittings
I N S T
L L
T I O N I N S T R U C T I O N S
Installation Instruction No.: 1 009 726 – February 2011
PRODUCTS COVERED:
Entrance End Fitting (OFR10 )
1. Remove KOs as necessary. To remove 1/2" trade size KO
(inner KO) orient as shown in 1 . To remove 1 1/4 in
trade size KO (outer KO), orient as shown in 1B.
1
3. Using #8 fasteners, install base of End Fitting directly on
top of existing floor covering. The screw type should be
appropriate for the type of floor, which the raceway is
being installed on.
OFR10 , OFR89-2400, OFR89-4000, OFR89-DS4000, OFR-VL
1B
Legrand/Wiremold electrical systems conform to and should be properly
grounded in compliance with requirements of the current National
Electrical Code or codes administered by local authorities.
ll electrical products may present a possible shock or fire
hazard if improperly installed or used. Legrand/Wiremold electrical
products may bear the mark of a Nationally Recognized Testing
Laboratory (NRTL) and should be installed in conformance with current
local and/or the National Electrical Code.
IMPORT NT: Please read all instructions
before beginning.
2.
ttach conduit fitting to KO and connect to conduit.
4. Slide raceway base onto End Fitting connecting tabs
and tighten #8-32 screws to secure.
5.
ttach Divider to End Fitting base in the desired
orientation. If the center position is used, the
breakaway tab must be removed from the divider.
loading

Resumen de contenidos para LEGRAND Wiremold OFR Serie

  • Página 9 Todos los productos eléctricos pueden presentar una posible descarga o riesgo de incendio si no son utilizados o instalados adecuadamente. Los productos Legrand/Wiremold pueden llevar la marca del Laboratorio de Pruebas Reconocido a Nivel Nacional (NRTL, por sus siglas en inglés) y deben ser instalados conforme el Código Eléctrico Nacional y/o local...
  • Página 10 6. Sujete la cubierta de la canaleta para cables. 7. Sujete la cubierta del accesorio terminal utilizando (4) tornillos de cabeza redonda n.º 6-32. ccesorios de transición de canaletas para cables (OFR89-2400, OFR89-4000, OFR89-DS4000) 1. Utilizando sujetadores n.º8, instale la base del accesorio 2.
  • Página 11 ccesorios de transición Vista Point5 (OFR-VL) 1. Retire el panel de acceso inferior del Vista Point5. 2. Retire las placas del adaptador de tubos de la base de Vista Point5. 3. Utilice un cuchillo navaja para retirar el borde de la 4.
  • Página 12 60 Woodlawn Street • West Hartford, CT 06110 1-800-621-0049 • F X 860-232-2062 • Outside U.S.: 860-233-6251 Canada: 570 pplewood Crescent • Vaughan, Ontario L4K 4B4 1-800-723-5175 • F X 905-738-9721 1 009 726 0211 © Copyright 2011 Legrand/Wiremold ll Rights Reserved...