Tabla de contenido
Idiomas disponibles
Idiomas disponibles
REMOTE CONTROL SWITCH – WATERPROOF IP45 (cod.SW3500)
MANUAL INSTRUCTION
Congratulations for your purchase of our WIRELESS SW3500 REMOTE SWITCH! The product that you have purchased was designed and constructed
specifically for use with Star Progetti infra red ray appliances.
WARNING
. Read the contents of this manual carefully before using the product. Star Progetti declines all responsibility for any personal injury or damage to
objects caused by failure to comply with the directions provided below. Compliance with these directions will ensure the device's electrical and
mechanical durability and reliability. This manual must be kept at hand for use as and when required.
. This device must not be used by children, by physically disabled or visually, hearing, mentally impaired persons, or by persons with no experience
of use of, and familiarity with, the appliance, unless supervised by, or under the direction of, a person responsible for their safety. Children must be
supervised, to make sure they do not play with the appliance.
. Do not use the remote switch when connected to extension cords.
1. CHARACTERISTICS
The mod. SW3500 remote switch was designed for use with radio transmission and remote control unit for turning Star Progetti heaters on and off.
The SW3500 remote switch is provided with remote control unit and 9V battery. All electrical appliances connected to the SW3500 remote switch
can be turned on or off either by means of the remote control unit, or manually by switch. The red indicator (LED) light on the switch indicates
function status: ON –OFF.
This device is user-friendly.
2. CONFIGURATION
1. Heaters can be turned on or off either by means of the remote control unit, or directly by switch (ON/OFF). The LED on the switch indicates
function status.
2. Remote control unit. For turning on and/or off.
3. INSTALLING
1. Unscrew the 4 screws on the back of the switch. Open the cover.
2. Connect the power cord to the clamp (N-in, L-in, G-in ).
3. Connecting the heater/s (maximum power: 3500 Watts). Connect the heater/s to the output terminal board (N-out, L-out, G-out ).
mm2 cord.
4. Before closing the switch, make sure the water-resistant seal is in its seat. Make sure that the front flap is also fully closed. The switch MUST BE
MOUNTED VERTICALLY ON THE WALL. The front flap must open downward.
5. Remote control unit. Open the battery housing cover. Insert the 9V battery. The LED indicator light then starts to blink. Press any button.
4. SETTINGS – FUNCTION WITH REMOTE CONTROL UNIT
1. Set the remote control unit and the switch with the LEARN button on the switch.
2. Press the LEARN button on the switch. The red indicator light (LED) blinks. This indicates that the switch is in the LEARN position
(settings).
3. Press one of the "ON/OFF" buttons on the remote control unit (button A, B or C). The red indicator light (LED) stops blinking.
4. The setting operation has been completed. The device is controlled by the button which has been selected. Other switches to be controlled by
means of the one remote control unit (up to 3 switches) can be set as described here, using A for one switch, B for a second switch and C for a third
switch.
5. All devices set can be turned on and off by means of the ALL ON and ALL OFF button.
6. WARNING – The red RESET button resets all previous settings. Press and hold the RESET button for about 3 seconds. The indicator light shall
start to blink and all stored data shall be reset.
5. TECHNICAL DATA
● Power: max 3500 Watts per switch
● Radio frequency: 433.92 MHz
● Rated voltage: 125~250 V - 50~60 Hz
● Rated current: 16A
● Degree of protection: IP45 – water-stream jet proof
● Controller stand-by current: ≤5μA
● Working temperature: 0°C-35°C
● Working range: 25 metres (no obstacles - device works also through walls)
Use 3x1 mm2 cord.
ENGLISH
Use a 3x1
Tabla de contenido
