Electromagnetic Fields (Emf) - Philips GC651 Manual Del Usuario

English
introduction
Thanks to its compact, lightweight design, this iron is ideal
for quick ironing jobs or for taking it along in its handy
pouch when you are travelling. The iron can safely be
used at all mains voltages (110-120V/220-240V), as it
is equipped with a voltage selector. If needed, suitable
adapter plugs are available from Philips dealers, service
centres, hotel receptions or hardware shops.
general description (Fig. 1)
A Steam boost button
B Steam control
C Temperature-ready indicator
D Cap of filling opening
E Filling opening
F Dual voltage selector
G Temperature control
H Mains cord
I Grip area
J Soleplate & button groove
Not shown: Pouch (GC651/650 only)
Not shown: Tablecloth (GC651 only)
important
Read these instructions for use carefully before using the
appliance and save them for future reference.
Check if the dual voltage selector has been set to
,
the local mains voltage before you connect the
appliance.
You can adjust the position of the dual voltage selector by
means of a pen.
It is advisable to always reset the selector to
,
position 220/240 after use. This will prevent damage
if the iron is inadvertently connected to the wrong
voltage.
Use an earthed adapter plug if the mains plug does
,
not match the local wall socket.
Only connect the appliance to an earthed wall
,
socket.
Do not connect the appliance to a wall socket
,
intended for shavers.
Do not use the iron in your hotel room
,
simultaneously with another high-wattage appliance
(e.g. a hairdryer) to avoid blowing the fuse.
Do not use the appliance if the plug, the cord or
,
the appliance itself shows visible damage, or if the
appliance has been dropped or is leaking.
Check the cord regularly for possible damage.
,
If the mains cord is damaged, it must be replaced
,
by Philips, a service centre authorised by Philips
or similarly qualified persons in order to avoid a
hazard.
Never leave the appliance unattended when it is
,
connected to the mains.
Never immerse the iron in water.
,
Keep the appliance out of the reach of children.
,
The soleplate of the iron can become extremely
,
hot and may cause burns if touched.
Do not allow the cord to come into contact with
,
the soleplate when it is hot.
When you have finished ironing, when you clean
,
the appliance, when you fill or empty the water
tank and also when you leave the iron even for a
short while: set the steam control to position O,
put the iron on its heel and remove the mains plug
from the wall socket.
Always place and use the iron on a stable, level and
,
horizontal surface.
This appliance is not intended for regular use.
,

Electromagnetic fields (EMF)

This Philips appliance complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and in accordance with the instructions in this
instruction manual, the appliance is safe to use according
to scientific evidence available today.
Before first use
1 Remove any sticker or protective foil from the
soleplate and clean the soleplate with a soft cloth.
Preparing for use
Filling the water tank
Make sure the appliance is unplugged and the steam
,
control is set to position O (no steam).
1 Open the cap of the filling opening. (Fig. 2)
2 Fill the water tank with tap water up to the
maximum level. (Fig. 3)
If the tap water is very hard, we advise you to use distilled
water.
Do not fill the water tank beyond the MAX indication.
Do not put perfume, vinegar, starch, descaling agents,
ironing aids or other chemicals in the water tank.
3 Close the cap of the filling opening ('click'). (Fig. 4)
setting the temperature
1
Check the laundry care label for the required
ironing temperature.
- Synthetic fabrics (e.g. acrylic, nylon, polyamide,
1
polyester)
- Silk
1
- Wool
2
- Cotton, linen
3
2 Set the temperature control to the required ironing
temperature. (Fig. 5)
3 Place the iron on its heel. (Fig. 6)
4 Put the mains plug in an earthed wall socket.
The temperature-ready indicator goes on to
,
indicate that the iron is heating up. (Fig. 7)
5 When the temperature-ready indicator has gone
out, wait a while before you start ironing.
Tips
- If the article consists of various kinds of fibres, always
select the temperature required by the most delicate
fibre, i.e. the lowest temperature. If, for example, the
fabric consists of 60% polyester and 40% cotton, it
should be ironed at the temperature indicated for
polyester ( ).
1
- If you do not know what kind or kinds of fabric
an article is made of, determine the right ironing
temperature by ironing a part that will not be visible
when you wear or use the article.
- Silk, woollen and synthetic materials: iron the reverse
side of the fabric to prevent shiny patches.
- Fabrics that tend to acquire shiny patches should be
ironed in one direction only (along with the nap)
while applying very little pressure.
- Start ironing the articles that require the lowest
ironing temperature, i.e. those made of synthetic
materials.
Using the appliance
steam ironing
1 Make sure that there is enough water in the water
tank.
2 Select the required ironing temperature (see
section 'Setting the temperature'). (Fig. 5)
Steam ironing is only possible at temperature
,
setting .
3
3 Set the steam control to position
The iron will start steaming as soon as the set
temperature has been reached.
ironing without steam
1 Select the required ironing temperature (see
section 'Setting the temperature'). (Fig. 5)
2 Set the steam control to position O (no steam).
(Fig. 9)
ironing without ironing board
When you are travelling, an ironing board will often
,
not be at hand. In this case, spread the tablecloth
(GC651 only) or a folded terrycloth towel on a
firm, flat surface. (Fig. 10)
Make sure that the surface is heat- and moisture-resistant.
Do not use a glass or plastic surface.
Features
steam boost
This function provides extra steam to remove very
stubborn creases.
1 Make sure that there is enough water in the water
tank.
2 Select the required ironing temperature (see
section 'Setting the temperature'). (Fig. 5)
The steam boost function can only be used at
,
temperature setting
3 Press and release the steam boost button. (Fig. 11)
Cleaning
1 Remove the mains plug from the wall socket and let
the iron cool down for at least 30 minutes.
2 Clean the appliance with a damp cloth.
storage
1 Set the steam control to position O (no steam).
2 Remove the mains plug from the wall socket.
3 Let the iron cool down for at least 30 minutes.
4 Empty the water tank. (Fig. 12)
Note:The water may be hot.
5 Wind the mains cord round the appliance. (Fig. 13)
6 Store the appliance in the pouch.
Environment
Do not throw the appliance away with the normal
,
household waste at the end of its life, but hand it in at
an official collection point for recycling. By doing this
you will help to preserve the environment. (Fig. 14)
guarantee & service
If you need information or if you have a problem, please
visit the Philips website at www.philips.com or contact
the Philips Customer Care Centre in your country (you
will find its phone number in the worldwide guarantee
leaflet). If there is no Customer Care Centre in your
country, turn to your local Philips dealer or contact the
Service Department of Philips Domestic Appliances and
Personal Care BV.
\ . (Fig. 8)
.
3