Hama 00186438 Instrucciones De Uso página 5

G Operating instruction
1. Controls and displays
1. Air intake opening (both sides)
2. Air sensor
3. Air outlet opening
4. Display and operating display
5. Front panel
6. Fan
7. Holder for the front panel
8. Handle
9. Water tank
10. Valve cover
11. Storage container
12. Stopper
13. Covering cap
Operation on the device or remote control:
14. Humidify button: Humidi er On/Off
15. Anion button: Ion generator On/Off - generates negatively
charged ions (anions) and small amounts of ozone. This increases
the cleaning performance, as the anions combine with positively
charged dirt particles in the room air to form larger clusters. These
can then be ltered out more easily by the internal lters.
Warning - Ozone
Do not use this function if you are sensitive to ozone, in
bedrooms, in rooms where children are present and in rooms
with tobacco smoke. Pets might also feel disturbed.
16. Timing button: Running time preselectable from 1 - 8 hours
17. Filter button:
After lter change - reset button for lter change indicator
18. Sleep button: All indicators except the Sleep indicator go out and
the device operates in whisper mode to allow undisturbed sleep.
Pressing Sleep again brie y activates the display so that another
operating mode can be selected.
19. Speed button: Fan speed level 1 - 2 - 3 - 4
20. Auto button: Switching between the operating modes:
Automatic - Manual
Automatic: Device regulates fan speed independently according
to air quality
21. OFF/ON button: After plugging the device into a socket, the
OFF/ON indicator ashes. Touch the button to start the device -
Select the desired operating mode.
Control lamps
Sleep: lights up when Sleep mode (18) has been activated
Negative ion: lights up when the anion function has been
activated via button (15)
Manual: Manual operation - Automatic (Auto) or Sleep are not
selected. Fan speed can be selected via the Speed button (19).
Humidi cation: lights up when the humidi er function has
been selected via button (14). A humidity of between 40 and 60
per cent is recommended. Excessive humidity promotes mould,
bacteria and mites. Increasing the humidity takes some time.
Formaldehyde removal: lights up during automatic operation
Auto: Automatic mode selected via the Auto button (20). The
built-in air quality sensor controls the fan speed.
Filter:
Filter change indicator. Flashes when lter needs to be replaced. • The air puri er calculates a required lter change according to its
service life.
• The change indicator lights up when the lter should be replaced
to ensure su cient air puri cation.
• With daily use, the combi- lter should be used up after approx.
6 -12 months.
• Since the lter contains all the collected pollutants, it should only
be changed outdoors and with appropriate care against contact
contamination (gloves/respiratory protection).
• The lter is not washable.
• An unpleasant odour during operation may indicate that ltered
substances are decomposing in the lter (e.g. bacteria) and it
needs to be replaced or ventilated in the sun.
• Vacuum the lter and the inner housing every 1 to 2 months to
remove coarse dirt. Then place the lter outdoors in direct sunlight
for approx. 3 hours to dry it and eliminate any bacteria, viruses
etc. that may be present through the UV rays.
• Also hold the vacuum cleaner against the open sensor opening
(2) to clean it.
• The lter can then possibly be reused. The lter must be replaced
after 1 year at the latest. On the one hand, there is a risk that it
will no longer completely remove the particles mentioned from
the air or that the pollutant particles already in the lter will be
released again. The activated charcoal also loses its effect when
unpacked.
• After changing the lter, reset the indicator by pressing the Filter
button (17) on the device.
Displays
• Speed: Display of the set fan speed
• PM 2.5: in µg/m³; display of measured ne dust
particles with an aerodynamic diameter Ø 2.5µm (0.5 to 3.5µm).
Typical concentrations in homes are 20 to 30 µg/m³.
• Air Quality: After switching on the device, the display ashes
until the sensor has warmed up. After that, the display visually
shows the indoor air quality.
Green stands for good quality
Orange stands for normal quality
Red stands for poor quality
• If the humidity in the room is very high, condensation can form on
the sensor and negatively affect the display and cause switching
back and forth in automatic mode. In this case, use the air puri er
with a manual speed setting.
88
• Temp/Humidity: Display alternates between the indoor
°C
TEMP
%
HUM
air temperature and humidity display.
• Timing: Display of the running time preselected via the Timing
button (16)
3