NOCS NS2 AIR MONITORS Manual Del Usuario página 4

ENglIsh
The Nocs Ns2 air Monitors are a set of active speakers with airplay
technology, allowing you to stream music wirelessly from your Mac, pC,
ipod touch, iphone and ipad. Turn your device into the ultimate music
experience and enjoy the powerful sound from the Ns2.
1. aBOUT airplay
airplay is a revolutionary technology that lets you stream music wirelessly
from your Mac, pC or iOs device.
2. gETTINg sTaRTED
The Ns2 has been designed to offer a simple and convenient airplay
solution.
2.1 UNBOXINg aND CONNECTINg
When unboxing the NS2 for the first time, it is advised to get familiar
with the product. after unboxing the Ns2, the power supply needs to be
connected to the right side speaker and the two speakers connected
using one of the two supplied speaker cables.
2.2 sWITChINg ON aND OFF
› switch on the Ns2 by pressing the "power" button located on the
right side speaker's rear panel.
› If the NS2 has not been setup before, the LED flashes green quickly
for about 30 seconds while booting up, followed by flashing green
slowly to indicate that the Ns2 is ready to be setup.
› If the NS2 has already been properly setup, the LED flashes green
quickly for about 30 seconds while booting up, followed by flashing
green slowly for 5 seconds. When the lED turns solid green followed
by a beep, the Ns2 is connected to the wireless network.
› To switch off, press the "power" button.
2.3 UNDERsTaNDINg ThE lED INDICaTOR
see separate table.
3. FIRsT TIME sETUp
The Ns2 needs to be connected to the same wireless network as the
Mac, pC or iOs device.
04 / ENglIsh
Note 1. The NS2 supports DHCP and will automatically re-connect to the
wireless network after the first-time setup.
Note 2. Moving the NS2 to a new wireless network or changing the
wireless network settings requires a new setup.
3.1 aUTOMaTIC sETUp UsINg WI-FI pROTECTED sETUp, Wps
If the wireless router supports Wps the setup is automatic.
a. switch on the Ns2.
B. The LED flashes green quickly for about 30 seconds while booting
up.
C. The LED flashes green slowly to indicate that the NS2 is ready for
setup.
D. press the "Wps" button on the wireless router.
E. press the "setup" button on the right side speaker's rear panel for
one second.
F. The LED flashes green/amber slowly to indicate that the NS2 enters
Wps mode.
g. The Ns2 automatically connects to the wireless network. If the
wireless signal isn't strong enough, the Ns2 will keep trying to
connect while the LED flashes green/amber slowly.
h. The lED turns solid green followed by a beep to indicate that the
Ns2 is connected to the wireless network.
I. If you wish to change the name of the Ns2 you open its Ip address
in a browser, then type in your selected name in the "airplay device
name" box and press "Update". please see the router manual for
instructions on how to retrieve Ip addresses. For airport Express
open AirPort Utility > Select the AirPort Express > Advanced >
Logs and Statistics > DHCP Clients and locate the Ns2 in the list
of clients.
Note 1. WPS requires an encrypted network.
Note 2. If the automatic setup fails, please run the manual setup instead.
3.2 MaNUal sETUp UsINg MaC, pC OR iOs DEvICE
If the wireless router does not support Wps, a manual setup is required.
Make sure you know the name and password of the wireless network
before you start.
a. switch on the Ns2.
B. The LED flashes green quickly for about 30 seconds while booting up.
The LED flashes green slowly indicating that the NS2 is ready for
setup.
C. Press and hold the "Setup" button for 5 seconds. The LED flashes
green/amber slowly indicating that the Ns2 has entered manual
setup mode.
D. Connect your Mac, pC or iOs device to the "NOCs_Ns2_setup"
wireless network.
E. Open http://192.168.1.1 in a browser.
F. If you wish to change the name of the Ns2, type in the selected
name in the "airplay device name" box and click "Update", then
return to the "Network Configuration".
g. select the wireless network (ssID) to which the Ns2 should be
connected and enter the network password. Use "advanced"
settings if needed. press "apply".
h. The LED flashes green quickly while the NS2 is rebooting, followed
by flashing green slowly while connecting.
I. The lED turns solid green followed by a beep to indicate that the
Ns2 is connected to the wireless network.
Note 1. It is recommended that the DHCP checkbox remains checked.
Note 2. In areas with a lot of Wi-Fi interference, connecting to the NS2
wireless network sometimes requires more than one attempt.
4. UsagE
Once the setup is finished, the NS2 can be fully operated from a Mac,
pC or iOs device.
4.1 MaC OR pC
a Mac or pC can output audio from iTunes by selecting the Ns2 from the
device menu in the bottom right corner of the program window.
COlOR MEaNINg
No color Off
solid green Connected
Slow flashing green Connecting
Fast flashing green Booting up
solid amber Network problem
slow Flashing amber Firmware update
Fast flashing amber Firmware error
Flashing green/amber setup mode