MTD 19A70051OEM Instrucciones De Instalación
MTD 19A70051OEM Instrucciones De Instalación

MTD 19A70051OEM Instrucciones De Instalación

Kit de abono rzt de 34 pulgadas
Idiomas disponibles

Idiomas disponibles

I
nstallatIon
34-inch RZT Mulch Kit — 19A70051OEM
Model 19A70051OEM mulch kit is designed for use with select
34-inch two-blade cutting decks. Refer to your tractor's
Operator's Manual to assure compatibility.
Carton Contents
Before beginning installation, remove all parts from the carton to
make sure everything is present. Carton contents are listed below
and shown in Figure 1-1. Part numbers are shown in parentheses.
Two Mulching Blades (742-05067)
One Deck Mulch Plug Assembly (631-05440)
One Wing Knob (720-04122)
Figure 1-1
Blade Installation
WARNING:
Before beginning installation, place
the tractor on a firm and level surface, set the
parking brake, place the PTO in the disengaged
(OFF) position, stop the tractor's motor and remove
the ignition key to prevent unintended starting.
WARNING:
Cutting blades are sharp. Always
protect hands by wearing heavy leather work gloves
to grasp blades.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
I
nstructIons
1.
Remove the cutting deck from beneath the tractor as
instructed in your tractor's Operator's Manual.
2.
Gently flip the deck over to expose its underside.
3.
Stabilize one of the cutting blades with a blade lock tool or
a block of wood. See Figure 1-2.
4.
Remove the hex flange nut that secures the blade to the
spindle.
IMPORTANT:
The hex flange nuts have a right-handed
(normal) thread pattern. Do NOT attempt to force the nuts in the
opposite direction. Doing so may damage the nuts.
5.
Repeat steps 3 and 4 on the other cutting blade.
6.
Replace the blades just removed, with the blades included
in this kit. Be sure to install each blade with the side marked
''Bottom'' (or stamped with a part number) facing the
ground when the mower is in the operating position.
IMPORTANT:
Use a torque wrench to tighten each blade hex
flange nut to between 70 ft-lb and 90 ft-lb.
Figure 1-2
Form No. 769-12125
(March 23, 2017)
Tabla de contenido
loading

Resumen de contenidos para MTD 19A70051OEM

  • Página 1 34-inch RZT Mulch Kit — 19A70051OEM Model 19A70051OEM mulch kit is designed for use with select Remove the cutting deck from beneath the tractor as 34-inch two-blade cutting decks. Refer to your tractor’s instructed in your tractor’s Operator’s Manual.
  • Página 2 Mulch Plug Installation IMPORTANT: Be certain that the bottom of the mulch plug is installed down inside of the lip of the deck opening, as Pivot the chute deflector upward and remove the shown in Figure 1-5. protective cover from the threaded pin found on the deck’s surface.
  • Página 3: Contenido De La Caja

    InstalacIón Kit de abono RZT de 34 pulgadas — 19A70051OEM El kit de abono del modelo 19A70051OEM está diseñado para ser Retire la plataforma de corte de la parte inferior del tractor, utilizado con plataformas de corte de dos cuchillas seleccionadas como se indica en el Manual del Operador del tractor.
  • Página 4: Instalación Del Tapón Para Abono

    Instalación del tapón para abono IMPORTANTE: Asegúrese de que la parte inferior del tapón para abono esté instalado abajo, en el interior del borde de la Haga pivotar el deflector del canal de descarga hacia arriba abertura de la plataforma, como se muestra en la Figura 1-5. y quite la cubierta protectora de la clavija roscada que se encuentra en la superficie de la plataforma.
  • Página 5: Installation Des Lames

    AVERTISSEMENT : Les lames de coupe sont tranchantes. Lorsque vous manipulez les lames, portez toujours des gants en cuir pour vous protéger les mains. MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Formulaire n 769-12125 (23 mars 2017)
  • Página 6 Installation du bouchon de déchiquetage IMPORTANT: Assurez-vous que le dessous du bouchon de déchiquetage est bien placé sur le rebord de l’ouverture du Relevez le déflecteur d’éjection et retirez le capuchon de plateau de coupe. Voir Figure 1-5. la goupille filetée qui se trouve sur la surface du plateau de coupe.
  • Página 7 Notes...

Tabla de contenido