Control Panel; Air Cleaner Set-Up - Electrolux Oxygen EAP150 Libro De Instrucciones

CONTROL PANEL

■
■
■
EAP150
G. AIR QUALITY SENSOR: Automatically monitors the air
EN
quality level.
H. Reset: Resets the "Check Filter" indicator light.
I. Check Filter indicator: Signals when to replace filters.
J. AIR QUALITY indicator: Lights indicate the quality of the air.
K. Fan speed indicator: Shows current fan speed setting (High
/ Med / Low / Sleep).
L. Fan speed selector: Adjusts fan speed setting (High / Med /
Quiet).
M. On-Off: Turns the unit "On" and "Off".

AIR CLEANER SET-UP

■
■
■
EAP150, EAP300, EAP450
Place the unit away from drafty areas, as the sensors may not
react accurately. Do not place near curtains, furniture, or other
items that might inhibit air flow. Place the unit on a stable
surface.
1. Remove protective film from the control panel.
2. Remove the front panel by pulling gently from the lower
portion of the panel.
Do not force; the panel should remove easily.
■
■
■
EAP150
3. Remove the HEPA 13 filter and the Carbon Pre-Filter from the
plastic wrapper.
4. Install the HEPA 13 filter with the arrow showing "air flow"
pointing in toward the back of the air cleaner; the white tabs
at the top and bottom of the HEPA 13 filter will point out to
the front of the unit.
5. Install the Carbon Pre-Filter in front of the HEPA 13 filter.
6. Replace the front panel by hooking the panel on the top of
the unit. Swing the panel in by pushing gently on each side
of the unit and then lock it into place.
■
■
■
EAP300
3. Remove the HEPA 13 filter and the Carbon Pre-Filter from the
plastic wrapper.
4. Install the HEPA 13 filter with the arrow showing "air flow"
pointing in toward the back of the air cleaner; the white tabs
at the top and bottom of the HEPA 13 filter will point out to
the front of the unit.
5. Install the Carbon Pre-Filter onto the plastic frame by
pushing against all "hook and loop" squares on the back of
the frame.
40 www.electrolux.com
■
■
■
EAP300, EAP450
I. AIR QUALITY SENSOR: Automatically monitors the air
quality level and adjusts fan speed accordingly when in
"AUTO".
J. Reset: Resets the "Check Filter" indicator light.
K. Check Filter indicator: Signals when to replace filters.
L. AUTO: Automatically adjusts the fan speed according to the
amount of impurities.
M. PlasmaWave™: Shows that the technology is active.
N. AIR QUALITY indicator: Lights indicate the quality of the air.
O. Fan speed indicator: Shows current fan speed setting (Turbo
/ High / Med / Quiet).
P. Fan speed selector: Adjusts fan speed setting (Turbo / High /
Med / Quiet).
Q. On-Off: Turns the unit "On" and "Off".
R. LIGHT SENSOR: Dims the control panel lights and sets the
fan speed to "Quiet" when the room is dark. (Only works
when is in "AUTO")
6. Install the plastic frame by inserting tabs up into the air
cleaner and gently pushing in at the bottom tab until the
frame fits into place gently.
Replace the front panel by hooking the panel on the top of
the unit. Swing the panel in by pushing gently on each side
of the unit and then lock it into place.
■
■
■
EAP450
3. Remove the Filter Cassette and remove the plastic wrapper
from it.
4. Install the Filter Cassette by inserting tabs up into the air
cleaner and gently pushing in at the bottom tab until the
frame fits into place.
5. Replace the front panel by hooking the panel on the top of
the unit.
6. Swing the panel in by pushing gently on each side of the
unit and then lock it into place.
■
■
■
EAP150, EAP300, EAP450
7. Plug the power cord into a wall outlet.
8. Press and hold the POWER button until a short "beep" sound.
9. The air cleaner will take 3~4 minutes to calibrate the air
quality sensor. During this time the sensor lights will flash on
and off.
■
■
■
EAP300, EAP450
10. Once the sensor has calibrated, the lights will be on "AUTO"
mode.