Tabla de contenido
Idiomas disponibles
Idiomas disponibles
GB
OBSERVE THE FOLLOWING INSTRUCTIONS
Place of work
The place of work must be properly illuminated and clean. Disorder and poor illumination may be a cause of accidents. Do
not work with electric tools in explosive environments, or those which contain inflammable liquids, gases or vapours.
Electric tools generate sparks, which may cause a fire in case of contact with inflammable gases or vapours. Do not allow
children and outsiders to the place of work. A lack of concentration may result in a loss of control over the tool.
Electric safety
The plug of the power supply cable must fit the mains socket. Do not modify the plug. Do not use any adapters whatsoever
in order to adapt the plug to the socket. Unmodified plug which fits the socket reduces the risk of an electric shock. Avoid
contact with grounded surfaces, such as pipes, heaters and refrigerators. Grounding of the body increases the risk of an
electric shock. Do not expose electric tools to precipitation or humidity. Water and humidity which gets into the electric tool
increases the risk of an electric shock. Do not overload the power supply cable. Do not use the power supply cable in order
to carry the tool or to connect and disconnect the plug from the mains socket. Avoid contact of the power supply cable
with heat, oils, sharp tools and moving elements. Damage to the power supply cable increases the risk of an electric shock.
In case work is realised outside closed areas, it is necessary to use extension cords designed for applications outside
closed areas. Using a correct extension cord permits to reduce the risk of an electric shock.
Personal safety
Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if you
are tired or under effects of medicines or alcohol. Even a moment's inattention during work may lead to serious injuries.
Always use individual means of protection. Always wear goggles. Using individual means of protection, such as dust-masks,
protective shoes, helmets and hearing protections permits to reduce the risk of serious injuries. Avoid accidental activation of
the tool. Make sure the switch is in the OFF position, before you connect the tool to the mains. Holding the tool with a finger
on the switch or connecting an electric tool when the switch is in the ON position may lead to serious injuries. Before you turn an
electric tool on remove all the spanners and other tools, which have been used for adjustments. A spanner left on rotating
elements of the tool may lead to serious injuries. Keep your balance. Maintain an appropriate position. It will permit to control
the electric tool in case of unpredicted situations during its operation. Use protective clothes. Do not wear loose clothes or
jewellery. Keep your hair, clothes and gloves away from moving elements of the electric tool. Loose clothes, jewellery or
long hair may get caught on moving elements of the tool. Use dust extractors or dust containers, if the tool is equipped with
any. Make sure they are properly connected. Using of dust extractors permits to reduce the risk of serious injuries.
Operation of the electric tool
Do not overload the electric tool. Use a proper tool for the given purpose. A correct selection of the tool for the given work
will result in a more efficient and safer work. Do not use the electric tool if the switch is not functioning properly. A tool which
may not be controlled by means of a switch is dangerous and must be repaired. Disconnect the plug from the mains socket
before any adjustment, replacement of accessories or storage of the tool. It will permit to avoid accidental activation of the
electric tool. Store the tool away from children. Do not allow untrained persons to operate the tool. An electric tool may be
dangerous in hands of an untrained person. Make sure the tool is properly maintained. Check the tool in order to detects
any unfitting or loose moving elements. Check whether the elements of the tool are not damaged. In case any damaged
elements of the tool are detected, they must be repaired before the electric tool is operated. Many accidents are caused
by improper maintenance of tools. Cutting tools must be sharp and clean. Properly maintained cutting tools are easier to
control during work. Use electric tools and accessories in accordance with the aforementioned instructions. Use the tool
in accordance with its purpose, taking into account the kind and conditions of work. Should the tool be used for other
applications than the ones it has been designed for, the risk of a dangerous situation increases.
Repairs
The tool may be repaired only by authorised service centres, which must use solely original spare parts. It will guarantee
a proper level of safety of operation of the electric tool.
OPERATING CONDITIONS
Under no circumstances is it allowed to operate a pump with a damaged connection cord or plug. In case any such damage
is detected, they must be replaced with new ones by authorised personnel, and after replacement it is required to carry out
measurements of the efficiency of the anti-electric shock protection.
The pump must be connected to the 230V/50Hz AC mains with neutral earthing and a circuit protection of a minimum rating
amounting to 6A.
Do not use the pump in swimming pools.
If the pump is installed in water reservoirs to which people or animals may have access, e.g. garden ponds, or within their
protection areas, then the power supply circuit must be equipped with a residual current device whose minimum rated current
O
P
E
R
A
T
I
N
G
I
N
S
T
R
U
C
T
I
O
N
8
Tabla de contenido
