NORAUTO N1200 Manual De Instrucciones página 112

- Press the adjustable LED lamp power button. You will hear an audible beep and the
adjustable LED lamp will turn on. The backlight will turn on for 10 seconds.
The LCD screen will continue to display the battery status and the unit will stay on until the
LED lamp power button is pressed to turn the unit off.
- Press the compressor power button. You will hear an audible beep, and the backlit LCD
screen will display the battery status as well as the compressor icon.
The unit will turn off automatically after one minute if no other action is performed.
- Whenever the clamps are properly connected to a dead battery, a beep will sound and the
backlit LCD screen will display the Battery Status Icon, Battery Voltage Indicator, the
Clamp Icons, and the "+" and "–" signs, as well as the flashing Jump Starter Icon. The unit
remains on until the clamps are disconnected from the battery.
- If the Jump Starter Power Switch is rotated to the on position and the clamps are not
connected to a battery, a two-second warning will sound every 10 seconds. The backlit
LCD screen will display the Battery Status Icon, Battery Voltage Indicator, the Clamp
Icons, and the "+" and "–" signs. The Alarm Icon and the Jump Starter Icon will flash. The
unit remains on until the Jump Starter Power Switch is switched off and then displays the
battery status icon and the voltage of digital display for 10 seconds before automatic shut
down.
- If the clamp connections to the battery's positive and negative terminals are reversed, the
backlit LCD screen will display the Battery Status Icon, Battery Voltage Indicator, and the
Clamp Icons. The Alarm Icon, the "+" and "–" signs and the Reverse Polarity Icons will
flash and the unit will emit a continuous audible beep until the clamps are disconnected
from the battery.
- When the unit is charging or recharging, the backlight will turn on for 10 seconds. The LCD
screen will continue to display the battery status and voltage indicator. The battery icon
bars will change from empty to full (low to high) repeatedly.
Note: The unit will turn off automatically once ALL functions are turned off.
CHARGING THE DEVICE
Only use the charger provided with the product.
This device is delivered partially charged.
Before the first use, charge the device using the mains charger adapter for 40 hours.
Never leave the booster connected to a 220V socket for more than 48 hours.
Recharging the battery after each use prolongs its lifespan; significant and frequent
discharges between charges and/or overcharging will reduce the life of the battery.
Over time, all batteries lose power through self-discharge, and more rapidly so if exposed to
high temperatures. Consequently, batteries must be periodically charged to compensate for
the loss of power due to self-discharge.
Check the battery charge status by pressing the USB power button. The LCD screen will
display the battery charge status. Please press the button again to turn USB off after
checking.
Ensure all the other functions of the device are disabled in order to optimise the charge.
HOW TO CHARGE
- If the battery charge level is at full capacity, four solid bars will display.
- If the battery is partially charged, two or three solid bars will display.
- If the battery is nearly empty, one solid bar will display. The unit should be charged at
this time.
- If the battery is completely empty, four blank bars will display. The unit MUST be charged
at this time or the unit's built-in low voltage protection will activate. The empty Battery
Status Icon will flash for a short period of time before automatic shut down. The unit will
not operate until the battery is recharged.
Insert the male connector of the mains charger into the jack input located behind the device,
and connect to the mains.
The product is charging if the bars progressively light up from the bottom to the top.
When the battery icon displays 4 full bars, this means that the battery is fully charged.
Once the charge has finished, disconnect the mains charger from the mains power socket,
followed by the male adapter.
STARTING THE ENGINE
1. Turn off the vehicle's engine and disable all accessories (radio, air-conditioning system,
headlamps, connected mobile phone chargers, etc.).
2. Ensure the vehicle is turned off and the handbrake is on.
3. Place the device in the most stable position possible, distancing yourself from the moving
parts of the engine (belts, fans, etc.).
111