Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
H-2394, H-2395, H-2396
π
H-2397, H-5512, H-6423
H-7932
RUBBER SPEED BUMP
STEEL SPIKE METHOD (ASPHALT H-2396)
FOR PERMANENT SPEED BUMP INSTALLATION
Recommended to secure rubber speed bumps to
asphalt surfaces.
Required:
• Rubber speed bump.
• One 1/2 x 14" rebar steel spike for each hole in the
speed bump.
• Gloves, safety glasses.
• Traffic cones, drums or barricades for securing site.
• Mallet.
• Heavy-duty electric drill.
• 1/2" masonry bit.
• Sledgehammer for driving spikes.
Spike
1. Position speed bump in its installation position. Using
its pre-drilled holes as templates, mark the location of
each hole on the asphalt surface.
2. Remove the speed bump. Using a high-speed
hammer drill with a 1/2" masonry bit, drill pilot holes
through the roadway surface of each marked location
to a depth of 3-4".
3. Make sure the surface is thoroughly clean and dry.
Reposition the speed bump in its installation position.
Drive each 1/2" rebar spike through the speed bump
and into the drilled hole until the spike is snug against
the surface of the pre-drilled hole in the speed bump.
PAGE 1 OF 6
1-800-295-5510
uline.com
INSTALLATION
LAG BOLT METHOD (CONCRETE H-2397)
FOR TEMPORARY INSTALLATION OR IF REMOVAL
OF SPEED BUMP IS NECESSARY.
Recommended to secure rubber speed bumps to
concrete surfaces.
Required:
• Rubber speed bump.
• One 1/2" lag bolt, one anchor and one washer for each
hole in the speed bump.
• Gloves, safety glasses.
• Traffic cones, drums or barricades for securing site.
• Mallet.
• Heavy-duty electric drill.
• 1/2" masonry bit.
• A second 3/4" masonry bit is required for anchors.
• Impact wrench or heavy ratchet.
1. Position the speed bump in its installation position
and, using its pre-drilled holes as templates, mark the
location for each hole on the concrete surface.
2. Remove the speed bump. Using a high-speed
hammer drill with a 1/2" masonry bit, drill pilot holes
through the roadway surface of each marked location
to a depth of 3-4".
Pour le français, consulter les pages 5-6.
CAUTION! Do not drive spikes beyond snug.
If driven too far, the spike may damage the
speed bump.
Lag Bolt
Washer
Anchor
Para Español, vea páginas 3-4.
0421 IH-2396
Manuales relacionados para Uline H-2394
Resumen de contenidos para Uline H-2394
- Página 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-2394, H-2395, H-2396 π H-2397, H-5512, H-6423 1-800-295-5510 H-7932 uline.com RUBBER SPEED BUMP INSTALLATION STEEL SPIKE METHOD (ASPHALT H-2396) CAUTION! Do not drive spikes beyond snug. If driven too far, the spike may damage the FOR PERMANENT SPEED BUMP INSTALLATION speed bump.
- Página 2 5. Reposition the speed bump in its installation position. Insert the bolt through washer and hole in the speed bump. Tighten with an impact wrench or heavy ratchet. Repeat for each hole in the speed bump. 1-800-295-5510 uline.com PAGE 2 OF 6 0421 IH-2396...
-
Página 3: Tope De Velocidad De Caucho
H-2394, H-2395, H-2396 π H-2397, H-5512, H-6423 800-295-5510 H-7932 uline.mx TOPE DE VELOCIDAD DE CAUCHO INSTALACIÓN MÉTODO CON CLAVO DE ACERO ¡PRECAUCIÓN! No introduzca los clavos más allá de lo que se considera "ajustado". (ASPHALT H-2396) Introducir el clavo demasiado podría dañar el tope de velocidad. -
Página 4: Continuación De Instalación
Inserte el tirafondo a través de la rondana y el orificio del tope de velocidad. Apriételo con una llave de impacto o trinquete. Repita para cada uno de los orificios del tope de velocidad. 800-295-5510 uline.mx PAGE 4 OF 6 0421 IH-2396... - Página 5 H-2394, H-2395, H-2396 π H-2397, H-5512, H-6423 1-800-295-5510 H-7932 uline.ca RALENTISSEUR EN CAOUTCHOUC INSTALLATION MÉTHODE AVEC PIQUETS EN ACIER MISE EN GARDE! N'enfoncez pas les piquets plus loin que « serré ». Si le piquet est trop enfoncé, (ASPHALTE H-2396) il peut endommager le ralentisseur.
- Página 6 Insérez un boulon à travers la rondelle et dans chaque trou du ralentisseur. Serrez à l'aide d'une clé à chocs ou d'un cliquet lourd. Répétez la procédure pour chaque trou du ralentisseur. 1-800-295-5510 uline.ca PAGE 6 OF 6 0421 IH-2396...