Technical Data; Installation Instructions - Grohe F-digital deluxe Manual Del Usuario

GB
Note: Read the complete installation instructions prior to installation.
They contain important information for safe and professional installation
in combination with other modules.
Safety notes
• Avoid danger due to damaged connection cables. In the
case of damage, the connection cable must be replaced by
the manufacturer or its customer service department or an
equally qualified person.
• Always switch off the power supply before performing any kind of work.
• The connectors must not be directly or indirectly sprayed with water
when cleaning.
• The voltage supply must be separately switchable.
• The light remains lit for one minute after the iPod is removed from the
docking station. All other functions are interrupted immediately.
• Children or adults with physical, mental and/or sensory limitations
are not permitted to use the product unsupervised.
• Persons under the influence of alcohol or drugs are not permitted to use
the product.
Applications/function
• Connection to the light, sound and steam modules.
The control box is the central unit used to control the light, sound and
steam modules via the app installed on the iPod in the docking station.
The following components can be connected:
• maximum of 4 lamps
• maximum of 4 speakers
• maximum of 2 power supply units
• 1 docking station
• 1 steam generator
• 1 feeler gauge

Technical data

See type plate fold-out page III, Fig. [4].
• Ambient temperature:
Electrical test data
• Software class:
• Contamination class:
• Rated surge voltage:
• Temperature for ball impact test:
The test for electromagnetic compatibility (interference emission test)
was performed at the rated voltage and rated current.
Approval and conformity
This product conforms to the requirements of the relevant EU
guidelines.
The conformity declarations can be obtained from the following address:
GROHE Deutschland Vertriebs GmbH
Zur Porta 9
D-32457 Porta Westfalica

Installation instructions

• Installation is only possible in frost-free rooms.
• The maximum permissible distance between the docking station and
control unit is 4,5m.
• The app required for the docking station function must first be installed
on the iPod:
- Direct connection of the iPod to the App Store via a wireless network
connection (an Apple account is required).
- Via iTunes in the iTunes Store (iTunes must be installed on the
computer and an Apple account is required).
- Via a link on the Grohe homepage www.grohe.com.
Please pass these instructions on to the fitting user!
The right to make technical modifications is reserved!
Installation:
Refer to the dimensional drawings on the title page.
Installation diagram for all modules, see fold-out page I and II.
• Vacant tubes (EN21/EN25) must be used for the cables leading from the
control unit to the modules, see Fig. [3]. Vacant tubes EN25 are only
required for the docking station.
• All cables must be pulled through using a pulling device to avoid damage.
• If there are more than four bends in a vacant tube, the cables must be
pulled through the tube prior to installation.
Distribution box and control unit, see fold-out page III and IV, Fig. [1] to [8].
1. Install the distribution box (A) on the floor and make slots for the
vacant tubes, see fold-out page III, Fig. [1].
2. Pull through the vacant tubes (EN21/EN25), see Fig. [3]. Vacant
tubes EN25 are only required for the docking station.
3. Pull through the cables as shown in Fig. [3] and [4] and plaster the wall,
making sure that the cable ends are the correct ones. Make sure that
the cable ends protrude a minimum of 300mm into the distributor box.
4. Mount the elbow (B), see fold-out page III, Fig. [2].
5. Screw the socket(s) (C) under the elbow (B), see Fig. [2]. If there are
more than four consumer devices, two sockets must be connected.
These sockets are not included in the delivery specification.
Electrical installation
Electrical installation work must only be performed by
a qualified electrician. This work must be carried out
in accordance with the regulations according to
IEC 364-7-701-1984 (corresponding to VDE 0100 Part 701)
as well as all national and local regulations.
6. Screw control box (D) into distributor box (A), see Fig. [5] and [6].
7. Remove the adhesive film from the power supply unit(s) (E) and attach
to elbow (B), see Fig. [7].
8. Establish all connections. Observe the type plate! Make sure that
speakers are always connected to the control box in pairs using
a Y-cable. A maximum of four speakers can be used. When using two
speakers, the Y-cable must be connected to the "Main" output on the
10 – 40 °C
control box, see type plate on fold-out page III, Fig. [4].
Important: Establish the connection between the control unit (D) and
A
power supply unit(s) (E) last of all. When using one power supply unit
1 only, the cable must be connected to the "Main" output on the control
2500 V
box, see type plate on fold-out page III, Fig. [4].
100 °C
9. Connect voltage supply via mains plug (G), see Fig. [8].
10. Place the lid and distributor box in position.
Refer to the relevant product information for a description on the
installation and function of individual modules.
2