HIKVISION DS-PD2-D15E Manual De Instrucciones

2
1: Disassembling the KX
DS-PD2-D15E
15m Dual Technology
Digital Detector
EN50131-2-4:2008
EN50131-1:2006+A1:2009
Security Grade (SG) 2
Environmental Class (EC) II
This product and - if applicable - the supplied
accessories too are marked with
"CE" and comply therefore with the
applicable harmonized European
2011/65/EU.
For electrical products sold within the European
Community. At the end of the electrical products
life, it should not be disposed of with household
Check with your local Authority or retailer for D The KX15DD Printed Circuit Board
®
recycling advice in your country.
The KX15DD Casing ® Wall Brack
4: Bracket Connec 5: Installa
EOL Resist ance
Headers
C2 C3
C AB L E E NT R Y
a) Ceiling
Do not par
K NO C K O UT
Pyro Sensor
Bracket
F
Avoiding False Alarms
Alarm LED
LEDs. Onc
O F F O N (D efault)
ready to use.
Ceiling Brack
1. Avoid placing the detector in direct sunlight.
C5
2. Do not let pets and other animals wander freely
LO W AU TO
whilst the alarm system is armed.
3. Do not mount the detector near heaters or
radiators.
b) Wall Bracket This is the default
F
4. Do not mount the detector near open windows or
air vents as draughts may cause false alarms.
The W or The KX15DD (Examples using 4k7 for alarm, 4k7 for tamper)
Normally Closed W iring Single End of Line W iring (SEOL)
10: Choose the Connec Type
E2
Control Panel Control Panel
a) Normally Closed b) Single End of Line Wiring
+AUX - Z 1 T T 5K6 6K8 +AUX - Z 1 T T
5K6
4K7
4K7
2K2
2K2
1K
ALARM CONTROL PANEL 1K ALARM CONTROL PANEL
ALARM CONTROL PANEL ALARM CONTROL PANEL
The
conne
+ - + -
+ – ALARM TAMPER LED + - + – ALARM TAMPER LED
6K8 5K6 6K8 shows the 5K6
5K6 4K7 5K6 4K7
4K7 2K2 4K7 2K2
2K2 2K2 example value
1K 1K
1K 1K
4k7 for tamper
(EOL).
® ®
KX15DD KX15DD
Zone Doubling Example (Matrix 424,832 or 832+)
Control Panel
6K8
5K6
5K6
4K7 4K7
+ -
+ - +AUX - Z 1 T T - + -
6K8 ALM ALM TAMPER ALM ALM TAMPER
ALM 2K2 ALM TAMPER 2K2
5K6
5K6
1K
1K 4K7
4K7
L ink
2K2
2K2
1K
1K
+AUX - +AUX -
+ – ALARM TAMPER LED
+ – ALARM TAMPER LED 5K6
6K8 5K6 6K8
5K6 4K7 5K6 4K7
4K7 4K7 2K2
2K2 TAMPER TAMPER
2K2 TAMPER ® 2K2 1K
1K KX15DD
1K 1K
Detector
KX
ALARM KX
ALARM
ALARM ALARM
12: The 15m Volumetric Lens 13: Dimensions and Weight
85°
60 zones
7 planes
ALARM CONTROL PANEL ALARM CONTROL PANEL
ALARM CONTROL PANEL
+ - + -
+ -
117 x 69 x 50mm
Link
Link Link
2K2
+ - 2K2
+ - + -
Hard Wired
Hard Wired
125g (4.4 oz)
Resistor
Resistor
+ - without bracket
+ - + -
ALM ALM TAMPER ALM TAMPER ALM ALM TAMPER
ALM ALM TAMPER ALM ALM TAMPER
13m according to EN 50131-2-4
MPER TAMPER
a) Printed Circuit Board
b) Light Pipe
e) PCB
Screw
f ) Back
Tamper
f ) Nut
d) Lens Collet
® g) Casing Screw
c) Lens E EOL Resistor Headers
Hints 6: S ty S
S E NS IT IVIT Y S E T T ING S : ®
The KX15DD has two set s of header pins on the PCB, one on
ALARM CONTROL PANEL
either side of the connector blocks. These headers are used to
Auto, High or L ow.
select the End Of Line resistance for EOL
a) Auto S ty (Default)
6K8 + – ALA RM TAMPER LED 5K6
5K6 completely obscure the detector's If EOL wiring is not used, leave the headers OFF
4K7
4K7 2K2
2k2 1K
1K S ee the diagams below
+ -
The set to the lef t of the + terminal select s the value of the
resist ance across the ALARM relay . The set to the right of the
TAMPER terminals select s the value of the End Of Line resistor
of the PCB If the resist ance value you require
is not select able, leave the
AUT O,
headers of f and wire a resistor
LOW AU TO AU TO HI HIGH or LOW . of the required value between the
appropriate terminals as shown.
T
tector is
please see the diagrams below .
+ -
ALM ALM
6K8 + – ALAR M T AMPER LE D 5K6 6K8 + – ALARM TAMPER LED
5K6 4K7 5K6
AU TO H I 4K7 2K2 5K6 4K7
2k2 LO W AU TO AU TO H I 4K7 2K2
1K 1K 2k2 1K
1K
TAMPER
LOW AU TO AU TO HI ALARM
LOW AU TO AU TO HI
®
Double End of Line W iring (DEOL) Remote LED Enable
E3 ®
Control Panel
The KX15DD has a terminal marked 'LED'
to enable the LED in walk test only on a alarm control panel.
c) Double End of Line Wiring
5K6 6K8 5K6
+AUX - Z 1 T T
This is used when the LED is disabled via the LED ON/OFF link.
5K6
4K7 4K7
4K7
2K2 2K2
To enable this feature, the LED terminal needs to be connected
2K2
1K 1K
ALARM CONTROL PANEL 1K ALARM CONTROL PANEL ALARM CONTROL PANEL to an Output at the alarm control p anel. When the system is ALARM CONTROL PANEL The
ALARM CONTROL PANEL
is in walk test mode the Output should be at 0V
conne
The Output would be usually programmed as "Remote LED
shows the
+ - + - enable". + - + -
+ - + – ALARM TAMPER LED + -
6K8 5K6
example
5K6 4K7
4K7 2K2
2K2
1K values of 4k7
1K
+ – ALARM TAMPER LED
for Alarm and
® 4K7 for tamper
KX15DD
(EOL).
Link
Two DEOL Detectors T o One Input
+ -
E5
Control Panel
6K8
5K6
5K6
4K7
+AUX - Z 1 T T
+ - + - + - 4K7
+ - + -
ALM ALM TAMPER ALM ALM TAMPER ALM 2K2 ALM ALM TAMPER ALM
ALM ALM TAMPER 6K8 ALM ALM 2K2 TAMPER
5K6 1K
1K
L ink
4K7
2K2
1K
+AUX -
+AUX -
+ – ALARM TAMPER LED + –
6K8 5K6 6K8
5K6 5K6
4K7
4K7
4K7 TAMPER 2K2
TAMPER TAMPER TAMPER 2K2
TAMPER 2K2 1K TAMPER ®
KX15DD 1K
1K
Detector
KX
ALARM KX ALARM KX ALARM KX
ALARM
ALARM
Coverage 85°, 60zones, and 7planes
Maximum Range 15m
85°
Op mal Installa on Height 60 zones 1.8-2.4m
Creep-Zone Protec on 7 planes Yes
RLNS074
Key features
Blue Wave Technology Yes
Automa c Sensi vity Yes
ALARM CONTROL PANEL
Digital ALARM CONTROL PANEL Yes
Separate Orange (Microwave), Blue (Alarm), Green (PIR)
3 Microwave Frequencies to Avoid Interference Yes
DEOL Resistors on Board + - Yes
+ -
Tamper Yes
Signal Strength Indicators (SSI) N/A
Wired
Power Supply 9-16 VDC (12VDC nominal)
Current 23mA
Current 30mA
Link
Link
2K2 Relay Type Solid state
+ - + -
+ - + - + -
Output Relay 60 VDC, 50mA protec on
Hard Wired
Tamper Terminal 12VDC max, 50mA max
Resistor
+ - + - + -
+ - + -
ALM ALM TAMPER ALM ALM TAMPER ALM
ALM ALM TAMPER
Hangzhou Hikvision Digital Technology CO.,Ltd.
TAMPER TAMPER TAMPER
2: The Printed Circuit Board
b) Mains Frequency
50Hz
(Default)
60Hz
c) S ty Auto/High
See Sec
d) AND/OR
See sec
e) ALARM LED
g) Pyro Sensor
DO NOT TOUCH
LED Disable
f ) Tamper and Alarm
LED Enable
Resistor Headers
(Default)
7: AND/OR Mode
ALARM CONTROL PANEL
b) High S ty
.
+ -
. AND
This symbol illustrates
where the resistors are
connected internally
Conven
+ -
be triggered simultaneously to generate an alarm)
TAMPER ALM ALM TAMPER
+ – ALARM TAMPER LED
6K8 5K6
5K6 4K7
LO W AU TO AU TO H I 4K7 2K2
2k2 1K
1K
OR
TAMPER
KX KX
ALARM
LOW AU TO AU TO HI
If either single technology detects prolonged
intruder ac
which can be used
d) Two Double End of Line Detectors to One Input
ALARM CONTROL PANEL
.
The conne
+ -
the example values
4k7 for alarm, 4k7 for
tamper (EOL).
Control Panel
Output
(0v in Walk Test)
2K2
+ - + -
Hard Wired
Resistor
+ - + -
+ -
TAMPER ALM ALM ALM TAMPER ALM TAMPER ALM
5K6
4K7
2K2
1K
ALARM TAMPER LED
5K6
4K7
2K2 TAMPER TAMPER
TAMPER
1K
Detector
KX KX
ALARM ALARM
ALARM
R INS 1038-3
Electrical
Microwave Frequency 10.515, 10.525, 10.535GHz
Alarm Response 2.5 second
Detec on Speed 0.3 to 3m/s
Op cs Sealed
Geometric 3D
Other Details
ALARM CONTROL PANEL
Opera ng Temperature -10°C to +40°C
Weight 125g
Dimensions(H x W x D) 117 x 69 x 50 mm
+ -
Accessories
Wall/Ceiling Brackets Included Yes
!
Link
The Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source according
+ -
+ -
to the IEC60950-1 standard. Please refer to technical sp cations for detailed information.
+ - + -
ALM TAMPER ALM ALM TAMPER ALM ALM TAMPER
ALM ALM TAMPER
This product operates in a
European non-harmonised
frequency band
No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
TAMPER TAMPER
+ -
3: Cable Entry + Moun
a) Terminals
b) Cable Entry
a) Moun Screw
Knockout
Knockouts
ALARM
h) Microwave
Poten ter
c) Case Lid Screw
F
8: Microwave Poten ter
ALARM CONTROL PANEL
+ -
microwave
+ -
+ -
ALM
Dual Tech (Both technologies need to
+ -
ALM ALM TAMPER TAMPER
ALARM
Minimum
Range (0m)
TAMPER
Maximum
KX
ALARM
Range (15m)
ty an alarm will be generated
ALARM CONTROL PANEL
ows
+ -
Link
+ -
+ -
ALM TAMPER ALM ALM TAMPER
TAMPER
Detector Detector
ALARM
15:
User Manual
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Manual") cannot be reproduced, changed, translated, or
About this Manual
This manual is applicable to detector.
latest version in the company website
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision's trademarks and logos are the
owners.
+ -
ALM ALM TAMPER ALM
TAMPER TAMPER
KX
ALARM
ALARM CONTROL PANEL
+ -
9: EOL Resistor Headers
Link
2K2
+ -
The device has 2 set of header pins at the top of
Hard Wired
the printed circuit board. These headers are used
Resistor
to select the End of Line resistance for EOL wiring
+ -
ALM TAMPER ALM ALM TAMPER
applica s.
If EOL wiring is not used, leave the headers OFF.
TAMPER
KX
ALARM
11: Powering Up
LEDs. Onc tector is
ready to use.

 READY
NOT READY
the party responsible for compliance could void the user's authority to operate
the equipment.
FCC compliance: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
frequency energy and, if not installed and used in accordance with the
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that