Tabla de contenido
Idiomas disponibles
Idiomas disponibles
en
ENGLISH
ECO position: The energy consumption
corresponds to energy class A+++. The maximum
inside temperature that can be reached is 8- 11°C
cooler than the outside temperature (at 23°C
outside temperature).
7.5
Opening / closing the lid
See Fig. A, Page 2.
Opening: To be able to open the lid (8): Fold the
carrying handle (9) backwards. Then fold the lid (8)
backwards.
Closing: Close the lid (8) and fold the carrying
handle (9) forwards.
7.6
Energy saving tips
- Do not expose to direct sunlight.
- In cooling mode: Use already cooled food and
beverages.
- Do not open the lid longer than necessary, close it
completely.
- Ensure that air can circulate between the food.
8. Cleaning
DANGER! Disconnect the device from the
power supply. Pull the plug, remove battery
pack. There is the risk of electric shock!
DANGER! Make sure that no liquid enters the
inside of the lid to avoid hazards!
Clean the lid using a slightly moistened cloth. Do not
use solvents or detergents that attack plastics.
Vacuum the ventilation slots or clean with a soft
brush.
Clean the inside of the container with water and
dishwashing liquid. Dry well.
9. Maintenance
9.1
Replace defective 12 V fuse
(if necessary)
See figure B, page 2.
1. Pull the 12 V plug (15)out of the cigarette lighter
socket.
2. Remove screw and remove lid.
3. Remove the fuse (16)and replace it with a new
fuse of the same design.
4. Attach the lid again and fasten it with the screw.
10. Troubleshooting guide
The device does not work:
- Check if the plug or battery pack are inserted until
the stop.
- If the current selector switch (7) is in "battery pack"
position: Check the charge status of the battery
pack (see chapter 6.2). Charge the battery pack if
necessary.
- If the current selector switch is set to 12 V: Switch
on the ignition of your vehicle.
- If the current selector switch is on 12 V: Replace
the fuse (see chapter 9.1).
- Is the device switched on from the rotary knob (3)
and on the operating mode switch (6)?
12
The device does not cool properly:
- Place the device in a cooler location. Do not
expose to direct sunlight.
- Ensure that the ventilation slots are not covered.
Sufficient air circulation must be ensured.
- Increase power: Turn power regulator (3) in
clockwise direction.
The device does not warm properly:
- Ensure that the ventilation slots are not covered.
Sufficient air circulation must be ensured.
- Increase power: Turn power regulator (3) in
clockwise direction.
11. Accessories
Use only original Metabo or
CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Chargers: ASC Ultra, ASC 30-36, ASC 145 DUO,
etc.
Battery packs with different capacities. Only
buy battery packs with voltage suitable for your
power tool.
Note: We recommend the use of battery packs >
4.0 Ah.
Order no.: 5.5 Ah 6.25368 (LiHD)
Order no.: 8.0 Ah 6.25369 (LiHD)
Order no.: 10.0 Ah 6.25549 (LiHD)
etc.
See www.metabo.com or the catalogue for a
complete range of accessories.
12. Repairs
Repairs to electrical equipment may only be
carried out by qualified electricians!
If the mains connection cable of this device is
damaged, it must be replaced by the manufacturer
or an authorized service centre to avoid hazard.
If any of your Metabo power tools require repairs,
please contact your Metabo service centre. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
13. Environmental Protection
The device / the insulation must be disposed of
properly. Combustible insulation blowing gas
(cyclopentane) is used.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
devices, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2012/
19/EU on used electronic and electric equipment
and its implementation in national legal systems,
Tabla de contenido
