Reelcraft LG3050 143 10 Instrucciones De Operación

Operating Instructions
50Ft Cord Reel 1300 Lumen LED Work Light
Model No:
LG3050 143 10
CAUTION: Read all instructions and warnings before operating!
SAVE THESE INSTRUCTIONS! READ ALL INSTRUCTIONS!
WARNING: To avoid serious injury or death from electrical
shock or fire.
DO NOT handle this fixture or try to plug it in when your
1.
hands are wet or damp or when you are standing on a wet or
damp surface or in water.
2. This fixture MUST ALWAYS BE USED in accordance with
all electrical and safety codes and ordinances, including
the most recent National Electric Code (NEC) and with the
Occupational Safety and Health Act (OSHA) Volume 1 on
General Industry Standards and interpretations.
3. ALWAYS make certain that the power source conforms to the
requirements on the fixture.
4. ALWAYS disconnect the power before servicing or inspecting
the fixture for any reason.
5. This fixture is ONLY FOR USE ON 110-120V circuits and
are equipped with approved 3 conductor cord and 3-prong,
grounded type plugs. TO REDUCE THE RISK OF ELECTRICAL
SHOCK, it should only be plugged into a properly grounded
3-prong outlet. DO NOT remove the 3rd prong or otherwise
try to modify the plugs. If the plug will not fit the outlet, have
the proper outlet installed by a qualified electrician.
6. FIXTURE IS NOT WATERPROOF and is not intended for use in
showers, saunas or in potentially wet locations. The entry of
moisture into the light may cause damage and void warranty.
7. This fixture is for INDOOR USE ONLY. DO NOT use in flam-
mable or explosive atmospheres. Potential ignition may
occur.
8. NEVER LOOK DIRECTLY INTO LIGHT SOURCE. LEDs are
extremely bright and can damage eyes with prolonged expo-
sure.
9. NEVER operate the light with the clear protective lens
removed.
10. KEEP AWAY from heating vents, radiators, or other sources
of heat.
11. KEEP OUT OF REACH OF CHILDREN.
INSTALLATION
Warning: All three screws with washers MUST be used when
installing mounting bracket. Eliminating one or more of the sup-
plied hex head screws may allow bracket to detach allowing reel
to fall causing damage to vehicles, injury or death.
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Wall Mounting
1. Pick the approximate location for the reel within 2 1/2 ft of a
110-125V Standard Ground Outlet.
2. Locate a stud to install the mounting bracket. The bracket will
be placed against the wall vertically, directly over the center of
the stud.
3. Using the bracket as a template, mark the (3) screw locations
with pencil. (Fig. 1)
4. Pre Drill (Pilot) the three screw holes with the use of at 1/4"
drill. The depth of the Pilot holes should be at least 2".
5. Install the bracket with the (3) provided Hex head wood
screws with washers using a 1/2" wrench or socket. Tighten
all three until snug. (Fig. 2)
2.56" (65mm)
Bracket hole pattern
Fig. 1
Bracket A
Fig. 2
ELECTRICAL RATING
Wall Mount
5Ft or Below
B
WARNING: DO NOT OVERLOAD! Check the amperages
A
of the tools or appliances to be plugged into the outlet of
this work light. Listed below is the maximum amperage
rating for this work light.
Cord Length Cord Type / Gauge
50 FT 14/3 SJTOW
C
Fig. 3
2.56" (65mm)
3 - #5/16" HEX SCREWS
Wall Mount
Above 5Ft
B
A
Maximum outlet rating
120V, 60Hz, AC, 1560 Watts,
13Amps
C
Rev: 7/2018
Fig. 4