Replacing The Battery; Charging The Battery - Peg-Perego Polaris RANGER RZR Empleo Y Manutencion

ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
ASSEMBLY
1 • Remove the 4 fixing screws from the two seat
base sections.
2 • Remove the seat base from the battery side
taking care to remove the connectors from the
slots.
3 • Remove the other seat base.
4 • Take out the battery and the battery base.
5 • Remove the fixing screws from the two rear
base fixtures.
6 • Remove the two rear base locks.
7 • Pull the base in the direction of the arrow to
fully remove the motor unit.
8 • Reposition and screw on both rear base locks.
9 • Insert the trailer attachment in the rear part,
ensuring that the 4 holes match precisely as
shown in the figure. Tighten the screws provided
(2 upper and 2 lower screws).
10 • Lift the two shock absorbers (1). Insert them
into the holes in the bodywork (2).
11 • Attach the shock absorbers to the bodywork
with the two pins (one each side). Note: the
packaging contains two spare pins.
12 • Insert the exhaust pipe as shown in the figure.
13 • Attach the exhaust pipe with the screw
provided.
14 • Position the rear box.
15 • Insert the tabs on the front of the rear box into
the bodywork (two each side).
16 • Fully insert the two metal tubes (one each side)
as shown in the figure.
17 • Attach the rear box with the three screws
provided. Important: the middle screw must be
tightened as shown in the following figure.
18 • Press the pin to help align the screw holes.
19 • Before fitting the side supports, check the picture
to make sure they match the grilles properly.
20 • Hook the lower ring of the support onto the
grille, as shown in the figure.
21 • Complete the attachment process by fitting the
upper ring. Make sure the front part of the grille
is inserted properly.
22 • Picture A shows the front part of the grille when
it is not yet fitted correctly. Picture B shows the
grille fitted correctly.
23 • Remove the 2 upper screws, as shown in the
figure, then take off the side panels of the
bodywork.
24 • Insert the side guards as shown in the figure,
taking care to fit the parts with the grid
extending towards the outside. Complete the
attachment by pushing the guards forward until
they click into position.
25 • Put the side panels of the bodywork back at the
2 points shown in the figure to secure them.
26 • Secure the upper profiles of the cargo box with
the screws provided.
27 • Complete the attachment of the rear box by
fastening the two screws inside the cabin.
28 • Rear cover plate:
• A - Housing for attachment to bodywork.
• B - Housing for the insertion of metal tubes.
• C - Housing for the insertion of the exhaust
pipe.
• D - Tabs for fixture to bodywork.
29 • Position the rear cover plate, matching the
various points marked with the letters A, B and
C.
30 • Lift the upper part of the rear cover plate to
facilitate the engagement of the tabs (D).
31 • Secure the rear cover plate with the two screws
as shown in the figure.
32 • Complete the attachment of the rear cover plate
by fastening the screw under the exhaust pipe.
33 • Install with pressure the vertical tube of the roll
bar showing in the drowing. Note: the pieces are
mirrored, as shown in the figure is the left.
34 • Rotate the vertical tube to facilitate the inclusion
of the side bars.
35 • Secure both vertical tubes using standard screw
provided.
36 • Secure the side bars to the vertical tubes with
screw.
37 • Place the back tubes. Note: The pieces are
mirrored.
38 • Fix the rear tubes at the top.
39 • Secure the rear tubes in the lower.
40 • Put the band of the central clamps on the rear
tubes (see proper orientation in the next
picture)
41 • The band should be horizontal and not towards
the top.
42 • Insert the central clamps into bands.
43 • Insert a screw and nut in the holes of the band.
44 • Secure the central clamps.
45 • Place the top of the rollbar. Mantain the holes
represented by the letter A on the front and the
holes represented by the letter B to the rear of
the vehicle.
46 • Secure seat belt and the top of the rollbar to
each vertical tube using screw provided in
separate bag.
47 • Attach the three plastic rings to rollbar. The
holes position is up and down the back of the
vehicle.
48 • Mount the three fog lights on the roof bars and
attach them with the screws provided (one per
light).
49 • Front cover plate:
• A - Tabs for fixing to the bodywork.
• B - Housing for engagement with the bodywork.
• C - Housing for attachment to the base
• D - Tab for engagement to the hood.
• E - Hole for inserting the front roll bar.
50 • Position the front cover plate by inserting the
points indicated with the letters A and B into the
bodywork. Put a hand inside the bodywork at
point B and squeeze it together with the mask to
click it into place (as shown in the circle).
51 • Press on the central area of the front cover plate
at the tab D to attach it to the hood.
52 • Press the lower part of the cover plate to engage
the two tabs C.
53 • Position the front roll bar, sliding it onto the
relevant pins.
54 • Take care with the bottom of the roll bar, which
must be inserted into the hole E of the cover
plate as shown in the picture.
55 • Attach the roll bar with the screw provided.
56 • Complete the attachment of the roll bar with
the two screws at the front.
57 • Press together the two sections of the steering
wheel to fully engage them.
58 • Insert the central steering wheel cap.
59 • Remove the plastic protectors from the steering
shaft.
60 • Position the steering wheel, aligning the holes
with those on the steering shaft.
61 • Attach the steering wheel with the threaded pin
and the bolt (the bolt must be inserted into the
hexagonal hole, the threaded pin in the circular
hole), holding the bolt to keep it in place.
62 • Insert the passenger's handle into the hole on
the dashboard.
63 • Attach the handle with the screws provided.
64 • Snap fit the petrol cap.
65 • Insert the seat base (removed previously) on the
driver's side.
66 • Insert the battery (charged previously) into the
compartment under the seat on the passenger's
side.
67 • Thread the battery plug and the electrical system
plug through the holes in the passenger's seat
base.
68 • Insert the seat base on the passenger side.
69 • Connect the battery and electrical system plugs.
70 • Fasten down the seat bases using 4 screws (two
on each side).
71 • Insert the two short sections of the safety belts
into the seat bases (in the holes near the gear
lever), taking care to insert all of the section of
belt highlighted in detail A. Note: the safety belt
buckle buttons must be facing the gear lever, as
shown in the figure.
72 • Unscrew the knobs from the seat base.
73 • Position the seat. Note: the seat can be adjusted
in length to two different positions, depending on
the height of the child.
74 • Screw the knobs back into position.
75 • Lower the seat.
76 • Tighten the safety screw. Repeat for the other
seat.
77 • Install the two parts of the windshield as shown.
Picture A shows the grille fitted correctly
78 • Secure the grille with the three screws.
79 • Place the windshield on the hood hooking the
three central tabs.
80 • Fit the windscreen of the vehicle with screws
81 • Remove the protectors from the rear axle.
82 • Insert the axle into the rear of the vehicle, as
shown in the figure.
83 • Position the driver in the inside of one of the
two larger wheels.
84 • Slide the wheel onto the axle with the driver
towards the vehicle.
85 • Slide a washer onto the axle.
86 • Fasten the wheel, tightening one of the four nuts
supplied with the spanner provided.
• Repeat the fitting operations for the other rear
wheel. Important: carry out the operations while
holding the axle still on the opposite side with
the help of the second spanner provided.
87 • Remove the protectors from the front axles.
88 • Slide a washer onto the axle.
89 • Slide one of the remaining wheels (narrower
than the rear wheels) onto the axle.
90 • Slide a washer onto the axle.
91 • Fasten the wheel, tightening one of the two
remaining bolts with the spanner provided.
• Repeat the fitting operations for the front wheel
on the other side.
92 • Snap fit the four hub covers onto the wheels.
FEATURES AND USE OF THE VEHICLE
93 • RADIO - Remove the two screws as shown in
the figure to extract the radio and insert the
batteries.
94 • Use a tool to lever the upper part of the radio
front panel and extract it.
95 • Release the screw on the battery compartment
cover.
96 • Insert two AA 1.5V batteries with the polarities
as indicated. Close the battery compartment
cover. Important: always tighten the screw.
97 • Insert the antenna and the radio into the housing
on the dashboard.
98 • Radio functions:
• A - Socket for an MP3 reader jack.
IMPORTANT!: Connect the MP3 reader (not
included) to the vehicle radio using a cable NO
longer than 150 cm.
• B - Radio station selector.
• C - On/Off buttons.
• D - Radio On indicator light.
• E - Volume control knob.
• F - Digital clock adjustment buttons.
99 • Driving cab features:
• A - Steering wheel.
• B - Fully functional radio (see fig 98).
• C - Passenger handle.
• D - Accelerator/electrical brake pedal
• E - Gear lever (see fig 100 - 101).
• F - Drinks holder (see fig 102).
• G - MP3 player storage compartment.
100 • GEAR LEVER: when supplied the vehicle speed
is limited to first gear (1 - see figure). It also
has a reverse (R), and a second gear (2)
recommended only for expert drivers. To
enable the second gear, unscrew the red stop
on the gear lever.
101 • Rotate the stop 90°, as shown in the figure, and
fix in position with the screw. Now by pulling
back the gear lever the vehicle can run in
second gear.
102 • DRINKS HOLDER - There are two drinks
holders for cans or bottles.
103 • REAR BOX and SUSPENSION - The rear of
the vehicle has a spacious cargo box and real
functional suspension on the wheels.
104 • WHEELS with RUBBER STRIPS Red Line
Nitrile Traction™ - The wheels are fitted with a
rubber strip for better grip on all surfaces,
silent performance and greater driving comfort.
105 • SAFETY BELT - To fasten the safety belt, insert
the end of the longer belt section into the
buckle on the shorter belt section, pushing the
two parts together.
106 • To release the safety belt, press the buckle
button and at the same time separate the two
elements.
107 • To change the length of the safety belt, move
the adjuster as shown in the figure.
108 • ACCESSORY: trailer to attach to the vehicle
(sold separately).

REPLACING THE BATTERY

PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
109 • Release the passenger seat safety screw and lift
the seat.
110 • Unscrew the knobs and remove the seat.
111 • Unscrew the two seat base screws. Disconnect
the battery and electrical system plugs.
112 • Extract the seat base and pull out the plugs.
113 • Replace the battery.
• Replace the seat base after passing the plugs
through the holes. Connect the plugs and
replace the seat.
114 • WARNING: always replace and tighten all the
knobs and screws.

CHARGING THE BATTERY

WARNING: BATTERY CHARGING AND ANY