Sears Kenmore 116.31912 Manual Del Propietário página 19

.;;.v///;;;.-/;;;%u•:iiii::::::.:::iii_i! ',••v - -.:. Hii::iiii .:_._j ;...;._j: :.:•j:;;;;:: • :.....%// ........... :..v._..._... j. ..-- -...-.v•......._._ _.:.;. _ ._•::: ;,/_•••,...v;;.%:_/:.:.;._j ..'/'•.'.'/.%'.'.'/•..;;;.V.•!_.II..._•%y/••••!II.'/L%-V;;.I
:::::::::::::::::::::::%::::::::::::::;::::::::::::::::::::: ::;::::;:: ::::: : ::: .::: ::::: , _ _ . • ;_ : :;::::::::::::::_ _::: i::::i:::.::::::::::::::::_::::::::::: : :::::_::::::: ::::::;:;_::::::::::::::::::::
iiiiiiiiiiiiiiiiiii_ _ iiiiiiiiiiiiiiiiiiii !!i!!i!iiiiiiiiii i_iii_i_! ! !!!ii!,__, " ,,i ". " .._ _ _' iiiiiiiiii ii ii _ i iii_iiiiiii_ _ i i _ii_i!i iiii
I
Review this chart to find do-it-yourself solutions for minor performance problems. Any service
needed, other than those described in this owner's manual, should be performed by an autho-
rized service representative.
_n_ _he un'mF_ilumtodo
Cleaner won'trun.
Poor job of dirt
pick-up.
Cleaner picks up
moveable rugsor
pushes too hard.
f. Unplugged at wall outlet.
2. Tripped circuit breaker/blown fuse
at household service panel.
3. On/Oft switch not turned ON.
4. Thermal protector tripped.
1. Full or clogged dust bag.
2. Wrong pile height setting.
3. Worn agitator•
4. Clogged nozzle or bag holder.
5. Clogged hose.
6. Hole in hose.
1. Plug in firmly, push On/Off switch to
ON.
2.. Reset circuit breaker or replace fuse•
:3. Push On/Oft switch to ON.
4. Allow vacuum to cool, then reset
Thermal protector (page 12).
1. Change bag, (page 15).
2. Adjust setting, (page 7).
3. Take to your nearest Sears
Service Center.
4. Check CLOG REMOVAL. (page 18).
5. Check for clogs, (page 18).
6. Take to your nearest Sears
Service Center.
7,
8,
9,
Ught won'twork. 1.
Agitator does not turn. 1.
2.
3,
4.
5.
Performanceindicator, 1.
some models, |s red. 2.
3.
4.
Air flow restricted 1.
with attachmentuse.
Sm_ndchar_jes. 2.
1. Dirt Sensor, some
models, will notwork.
Hose not inserted fully, 7,
Motor protectionsystem activated. B.
Dirty filters. 9.
Wrong pile height setting. 1.
Burned out light bulb•
Agitator On/Off selector in
OFF position.
Handte in foil upright position.
Hose removed from nozzle.
Agitator Overload tripped.
Thermal protector tripped.
Full or clogged dust bag.
Dirty lilters.
Clogged airflow passage,
Certain attachment tools.
Attachment use restricts air flow.
New carpet luzz dogged air path.
Dirty optic cells•
Insert hose fully, (page 10).
Check for clogs. (page 18).
Change filters. (page 16).
Adjust setting, (page 7).
1. Change light bulb, (page 17).
1. Move selector to the ON position,
(page 8).
2. Move handle from upright position
(page 7).
3. Reattach hose to nozzle (page 10).
4. Reset Agitator Ovedoad (page 12).
5. Allow vacuum to cool, then reset
Thermal protector (page 12).
1. Change bag, (page 15).
2. Change tilters, (page 16).
3. Clear clog from airflow passage,
(page 18).
4. This is normal. Light should go oft
when tool is removed.
f.
2.
Check ATTACHMENTS, (page 8)
Check CLOG REMOVAL and clean
hose, (page 18).
1. Clean optic cells. (page 13),
19