Unpacking The Machine; Technical Features; Preparation And Setup - Virutex TM72C Manual De Instrucciones

puede dirigirse a un Servicio Oficial de Asistencia
Técnica VIRUTEX.
En la inquietud continua por la mejora y actualización
de sus productos, VIRUTEX se reserva el derecho de
modificarlos sin previo aviso.
ENGLISH
TILTABLE MITRE SAW
With table top: Models TM72C and TM73C
Without table top: Models TS72C and TS73C
IMPORTANT NOTE
ATTENTION! Prior to using the machine, please read
carefully the GENERAL SAFETY INSTRUCTIONS
LEAFLET enclosed with the documentation.
Please keep the aforementioned LEAFLET and this MAN-
UAL in a safe place for future reference purposes.

1. TECHNICAL FEATURES

Model...........................................TM72C and TS72C
Version..................................................Single-phase
Motor.......................................................50 or 60 Hz
Power consumption......................................1,200 W
Service........................................................12/48 min
No-load speed (50 Hz)..............................3,000/min
Saw blade diameters.................................300x30 mm
Model...........................................TM73C and TS73C
Version..................................................Three-phase
Motor.......................................................50 or 60 Hz
Power consumption......................................1,300 W
Service........................................................12/48 min
No-load speed (50 Hz)...............................3,000/min
Saw blade diameters.................................300x30 mm
Turntable
Can be swivelled both right and left up to 45° with a
fixed lock position at 0°, 15°, 22°, 30', 30° and 45°. It
also allows fixation at intermediate degree settings.
Tiltable head
Swivelling from 90° to 45° as against the base and in any
position of the turntable, from 0° to 45° to the left.
Dimensions of the machine.....................(See Fig. 3)
Dimensions of the packing..............720x600x530 mm
Approximate weight
(without packing)...........30 kg (models with table top)
26 kg (models without table top)
2. MAXIMUM CUT CAPABILITIES
Cut at 0° x 90° (Fig. 9). See drawing A......80x150 mm
Cut at 0° x 45° (Fig. 12). See drawing B.....65x150 mm
Cut at 45° x 90° (Fig. 15). See drawing C...80x103 mm
Cut at 45° x 45° (Fig. 16). See drawing D....63x 60 mm
Cut on table top. See drawing E (*)...........max 35 mm
(*) for Models TM72C and TM73C only.

3. UNPACKING THE MACHINE

You will find the following elements inside the packing
case (Fig. 1):
For models TM72C and TM73C:
- Cut-off machine, according to the model
- Table square assembly
- Wood setting stop set
- Exhaust adapter
- Set of Allen wrenches 8mm
- Operation instructions and documentation
For models TS72C and TS73C:
- Cut-off machine, according to the model
- Wood setting stop assembly
- Exhaust adapter
- Set of Allen wrenches 8mm
- Operation instructions and documentation
For transport purposes, the machine head is locked in
its lower position. During unpacking, merely hold the
machine by the sides of the lower base and remove
it from the box. It is advisable for this operation to be
carried out by at least two people.

4. PREPARATION AND SETUP

ATTENTION! Make sure that the machine is unplugged
from the mains prior to carrying out any repairs or
maintenance operations on it.
4.1 INSTALLATION
For using the machine at a fixed spot, we recommend
its being coupled to a table or work bench at a height
of around 90 cms and using the holes A provided
on the base (Figs. 2 and 3). We recommend our
TRANSPORTABLE WORKING TABLE accessory
(Ref. 5800100)
The three-phase models of mitre saws have a factory
setting of 380 V. The user must implement a plug
suitable for his installations on the supply cable, but
always with a minimum capacity of 16 Amperes. In
addition, once the machine is connected to the mains,
it is essential to check that the blade turns in the direc-
tion indicated on the disc or the outside cover of the
machine. If the direction is not the same, the order
of two of the cables in the assembled mains supply
plug must be inverted.
This machine is foreseen exclusively for indoor work,
due to which it should not be placed in very damp
areas nor exposed to rain.
4.2 UNLOCKING THE HEAD
The machine leaves the factory with the head locked in
the correct position for transport. To unlock it, proceed
to press gently downwards on the handle (B) while
at the same time pressing on the orange colour lever
and pulling the knob "E" (Fig. 4) which is located at
the rear of the right hand side of the head, Turn it
90° until it comes to its normal resting position. Then
accompany the machine in its upwards movement to
its normal resting position.
7