Technical Data - Wieland SP-COP1 Manual Del Usuario

6

Technical Data

6.1 Technical data SP-SCOP1 / SC-COP2-xxx
SP-COP2-xxx
Safety Integrity Level SIL3 (IEC 61508)
SIL claim limit SILCL3 (EN 62061)
Category Category 4 (EN ISO 13849-1)
Performance Level (PL) PL e (EN ISO 13849-1)
PFHd (average probabil- see BA000966, Sec. Safety Specific
ity of dangerous failure Characteristics
per hour)
Mission time T 20 years (EN ISO 13849)
M
Protection class III (EN 61140)
Protection degree IP 20 (EN 60529)
Ambient temperature in –25 °C ... +65 °C
operation
Storage temperature –25 °C ... +70 °C
Humidity 10 % ... 95 %, non condensed
Vibration according 5 Hz ... 150 Hz, (EN 60068-2-6)
Shock proof
- continuous shock 10 g, 16 ms (EN 60068-2-29)
- single shock 30 g, 11 ms (EN 60068-2-27)
Electromagnetic Compa- Class A (EN 61000-6-2, EN 55011)
tibility
System connector Internal safety bus
Configuration Bus 1 USB-Mini-B
Configuration Bus 2 Ethernet-RJ 45 (SP-COP2-ENx only)
Dimensions (W x H x D)
- Screw terminal 45 x 96,5 x 121 mm
- Spring terminal 45 x 107 x 121 mm
Weight 290 g (± 5 %)
Terminals and connec- Screw type
tion data terminals
Single-core or finely
1 x 0,2–2,5 mm
stranded
2 x 0,2–1,0 mm
Finely stranded with
1 × 0,25–2,5 mm²
wire-end ferrule acc. to
2 × 0,25–1,0 mm²
DIN 46228
AWG (use Cu lines only) 26–14
Max. tightening torque 0.5–0.6 Nm
(5-7 lbf-in)
Single-core or finely 1 × 0.2–1.5 mm²
stranded
Stripping length 7 mm
Power Supply (A1, A2)
Supply voltage 24 V DC (16,8 ... 30 V DC)
Type of power supply PELV or SELV
With an external current limitation of 4 A
by the power supply or with a fuse.
Power consumption Max. 3,3 W
Attention: the power
consumption is in-
creased with every
connected module.
ON-Delay max. 18 s
Short-circuit protection 4 A gG
Power Supply B1 and B2 (B2: only SP-COP2)
Supply voltage 24 V DC (16,8 ... 30 V DC)
Type of power supply PELV or SELV
With an external current limitation of 8 A
per output group (B1 and B2) by the
power supply or with a fuse.
Power consumption 2 x 0,3 W
Short circuit protection 8 A gG
12
Spring type
terminals
2
2 x 0,2–1,5 mm²
2
2 x 0,25–1,5 mm²
24–16
̶
Input circuit
SP-COP1: (I1 ... I20)
SP-COP2-xxx: I1 - I16, IQ1 - IQ4
Number of Inputs:
SP-COP1 20
SP-COP2-xxx 20 (16 inputs fix, 4 inputs selectable)
Input voltage HIGH 13 ... 30 V DC
Input voltage LOW –5 ... +5 V DC
Input current HIGH Typ 2.3 mA / Max. 6 mA
Input current LOW < 2 mA
Input capacity
10 nF
Reverse current input at < 0,1 mA
measurement interrupt
Test output (T1 - T4)
Number of outputs 4 (with 4 groups of independent test
pulses)
Type of output PNP-semiconductor, push-pull, short-
circuit proofed
Output voltage HIGH U
Output current LOW -10 mA (limited)
Output current HIGH Single output: max. 120 mA;
sum of all testpulse outputs: max.
120 mA
Testpulse frequency 1 Hz ... 25 Hz, configurable
Testpulse duration 1 ms ... 100 ms, configurable
Load capacity 1 µF for testpulse duration ≥ 4 ms
0,22 µF for testpulse duration 1 ms
< 100 Ω
Resistance
Safety output:
SP-COP1: Q1 - Q4
SP-COP2-xxx: Q1 - Q4, IQ1 - IQ4
Number of outputs:
SP-COP1 4
SP-COP2-xxx 8 (4 outputs fix, 4 outputs selectable)
Type of output High-Side-MOSFET, short-circuit
proofed, current controlled
Output voltage High
U
Output current High ≤ 4,0 A
Max. overload current /
≤ 12 A / 8 ms
period
Sum current Isum Each output pair (Q1/2, Q3/4, IQ1/2,
IQ3/4)
≤ 45 °C
T ≤ 4,0 A
U
≤ 55 °C
T
≤ 2,5 A
U
≤ 65 °C
T
≤ 1,6 A
U
Output test,
deactivatable
Test pulse ≤ 450 µs
Test pulse rate
10 Hz
Leakage current Low < 0,1 mA
Load capacity 0,5 µF
< 200 Ω
Line resistance
Max. allowed coil energy < 0,125 J
without external protec-
tion
Reaction time Depends on logic extension
6.2 Approvals
 TUEV
 UL: The safety functions are not evaluated by UL. The approval is
accomplished according to UL 508, general use applications.
- 1,2 V
A1
≥ U
- 0,6 V
Qn Bx