227108_Kindred_KFPOS_Instructions_v2.qxd:130777_Faucet_Install_Instr.qxd
KFPOS Installation
1.
Before installing the faucet, open the hot and cold
water supply lines for several seconds to flush out
any scale, solder, or other impurities that would
otherwise damage the faucet. Then close the water
supply stops.
2.
Please note that stainless steel braided supply
hose (item 19) has been supplied and factory pre-
installed with the faucet (red indicates hot water
supply and blue indicates cold water supply).
3.
Disassemble poly locknut (item 1 8 x 1 pc.) and
metal flat washer/rubber flat washer (item 15 x 2
pcs.) from the faucet. Ensure that rubber o-ring
(item 14 x 1 pc.) is mounted to the base of faucet
before proceeding further.
4.
Insert the faucet body including spray head (item
29 x 1 pc.) and spray hose (item 24 x 1 pc.),
through the faucet hole (faucet hole must be a
minimum of 1 3/8" diameter and maximum 1 1/2"
diameter).
5.
Reassemble metal flat washer/rubber flat washer
(item 15 x 2 pcs.) and poly locknut (item 1 8 x
1 pc.) to faucet shank. If faucet is mounted
directly to sink ledge, use poly reinforcement
washer (item 16 x 1 pc.) between item 18 and
item 15. Note that plastic mounting bracket
(item 16 x 1 pc.) is intended only for installation
where the faucet is mounted directly to the sink
ledge. The plastic mounting bracket (item 16 x
1 pc.) is not necessary, and should not be used,
where the faucet is mounted to the countertop.
6.
Snug up assembly, but do not tighten.
7.
Rotate faucet body (item 9) from extreme right to
extreme left. Position faucet so that faucet body
(item 9) is centered within range of motion.
8.
Tighten poly locknut (item 18 x 1 pc.) so that
faucet is clamped to either sink or countertop,
with desired orientation.
9.
Assemble check valve (item 22) including fiber
washer (item 21 x 1 pc. and item 23 x 1 pc.) to
spray hose (item 24 x 1 pc.) and supply hose
(item 20 x 1 pc.). Fiber washer must be seated at
both ends of check valve to ensure watertight
connection.
10. Mount lead weight (item 25 x 1 pc.) at bottom of
spray hose loop (item 24 x 1 pc.).
1 1. Connect stainless braided supply hose (items 19)
to their respective supply lines.
12. Ensure that faucet lever is in the off position and
then turn water supply back on and check for
water tight seal. Retighten where necessary, but
do not overtighten.
1/4/10
10:07 AM
1
3
2
4
5
6
7
8
9
10
1 1
12
13
14
15
17
16
18
20
21
19
22
23
24
25
KFPOS Faucet Parts
01 Handle
16 Plastic Base
02 Screw
17 Metal Washer
03 Button
18 Nut
04 Cap
19 Supply Flexible Hoses
05 Cartridge Nut
20 Supply Tube
06 Cartridge
21 Fiber Washer
07 Housing
22 Check Valve Set
08 Teflon Ring
23 Fiber Washer
09 Body
24 Hose
10 O'ring
25 Weight
1 1 Insert
26 Plastic Insert
12 O'ring
27 Rubber Washer
13 Inner Body
28 Check Valve
14 O'ring
29 Pull Out Spray
15 Fiber Washer
30 Pull Out Spray Key
Page 3
29
30
28
27
26
Item No. KFPOS 01 10