Preparation For Use; Before Initial Use - Cloer 4709 Instrucciones De Uso

Dear Customer
We wish you much pleasure with your new
electric kettle.
Your Cloer Company

Preparation for use

·
Remove all packaging elements and labels, but
EN
not the rating plate.
·
Place the electric kettle on a dry, even, non-slip
surface.

Before initial use

·
Please read these operating instructions
carefully before using the device for the first
time.
·
Shake out the water from the first boiling
process.
Safety notices for use of the
contact base / electric kettle
The appliance meets the
requirements of the applicable
EC directives.
The appliance is intended
for in door use only.
·
Do not fill the electric kettle with water past the
MAX marking. Scalding may result from water
boiling over.
·
Always remove the electric kettle from the
contact base before filling with water.
·
This electric kettle may only be used for heating
water.
·
Before operating the machine, make sure that
the contact base is dry.
·
Please make sure that water is never spilled on
the contact base.
·
If water is accidentally spilled onto the contact
base, proceed as follows:
– Unplug the unit from the wall socket.
– Dry the contact base with an absorbent
dry kitchen towel.
– Dry the surface beneath the contact base.
– Plug the unit into the wall socket again.
Never operate the electric kettle without
the lid closed and without lime filter, since
then the device will not shut off automatically
when the water boils.
CAUTION!
The surface is hot during
operation. Only touch the
device at its handle.
ATTENTION!
Always unplug appliance when
not in use and before cleaning!
Operation
8
·
Plug the power plug into the wall socket.
·
Remove the electric kettle from the contact base.
·
Open the lid of the removable kettle by pressing
the button to open the lid.
·
NOTE: For your safety, the lid is equipped
with a locking device. If the electric kettle
is accidentally overturned during use, the lid will
not open. This reduces the risk of being scalded
by spilled water.
·
Fill the electric kettle with water.
·
Close the lid manually.
·
MAKE SURE not to fill water past the
maximum marking on the inside of the pot or
on the water level indicator.
·
Place the electric kettle anywhere on the contact
base. The unit is now ready for operation.
·
To switch it on, press the ON/OFF switch
on the bottom of the handle. The switch locks
into place and the control lamp lights up.
·
When the water boils, the electric kettle
automatically switches off and the control
lamp goes out.
·
You can interrupt the boiling process at
any time by pushing up the ON/OFF switch.
·
To pour the water, lift the electric kettle
from the contact base.
·
IMPORTANT: Always make sure that the device
is switched off before removing the electric
kettle from the contact base.
Removing the lid (4709 and 4909)
·
For removing the lid please note the following
steps:
– Let appliance cool off.
– Open lid.
– Press pushbutton in the middle of the lid.
– Remove lid up-wards.
·
CAUTION: Never operate the electric kettle
without the lid in place, as the device will
otherwise not shut off automatically when the
water is boiling.
Overheating protection device
The electric kettle is equipped with a double-
action overheating protection device. In the
event that you accidentally operate the electric
kettle without water or if the water level is too
low, causing the water to evaporate during
boiling, the device will automatically switch
off for your safety. The device will be ready
to operate once it has been filled with cold
water.
Cleaning
·
CAUTION: The appliance must not be immersed
in water! Do not clean the electric kettle with
heavily abrasive cleaners. They could scratch
the appliance.
·
Clean very dirty appliances either with lukewarm
water or with a stainless steel cleaner.
·
If a stainless steel cleaner is used, make sure
that it is not aggressive and does not contain
chlorine or acids.