Perles OF 9 Instrucciones página 14

Wires of the extension cable must have a minimum
2
section of 1,5 mm
unwound.
Plug in the tool only if the switch is turned off.
Always wear personal protective equipment, glasses
and footwear.
Always hold the router with both hands.
Switch off the motor after you have finished milling.
Before you put down the tool, loosen the router table.
Always put down the tool on a horizontal and clean
surface.
Do not put any other tools on the workpiece.
Workpiece must be clean, without any rests of
materials, sawdust ....
Work place should have adequte lights, it is forbiidden
to use the tool in rooms with inflammable substances
and gases, switch on/off the tool only by the switch
and not by disconnesting the plug.
Be careful of screws, nails and other objects in the
workpiece while milling.
Start working only when the tool has reached full
speed.
Be aware of the sudden impact when the OF9 power
tool is switched on.
Prevent unintentional switching on of the tool..
Always use undamaged and sharp router bits
When you do not use the tool, store it in a dry place
protected from dust.
Do not wear loose clothes of jewelry the tool could
take hold of and pull it towards it. If you have long hair,
wear a protective head-covering. When working
outside, wear non-skid footwear.
In case the tool is blocked, immediately switch off the
tool and disconnect the plug.
Clamp the workpiece.
Guide only switched on tool towards the workpiece.
Switch off the tool when you have lifted the tool from
the workpiece.
Use only original parts and accessories.
PREPARING THE TOOL FOR
MILLING
WARNING: Always disconnect the plug from
power source before making any adjustments
or changing any accessory.
Dust suction
Milling and grinding wood generate sawdust and dust
that endanger safety and health. Using dust suction
prevents air pollution for breathing and makes easier
removal of wastes.
Mounting dust extraction adapter
Put the dust extraction adapter
the twin column guide
extraction adapter.
Push the mouth with the right hand thumb in the direction
towards the locking edge
the periphery is automatically cought in the edge
Connect the hose of a vacuum cleaner directly to the
dust extraction adapter
hose with a turning connection for extracting dust
and the cable must be fully
baseplate so that
is inside the mouth of the dust
so that the lock
, or connect it with a suction
Fix the latter into the corresponding place below the
motor cover.
Mount the upper dust extraction adapter by pushing it in
the directions
gerabox and the motor cover. Then attach the lower part
of the hose to the dust extraction adapter
direction
Turning connection enables better view of the milling
area and setting the vacuum cleaner hose in the most
favourable position. The diameter of the dust extraction
adapter is 35 mm, which corresponds to hoses of
standard vacuum cleaners.
Removing dust extraction adapters
Upper dust extraction adapter
removed by first taking off the hose from the dust
extraction adapter
with the left hand thumb the upper part of the dust
extraction adapter in the direction
Lower dust extraction adapter.
the dust extraction adapter
periphery of the adapter
push in the direction of the arrow
adapter.
Choosing a router
Always use router bits of such diameters that
correspond the lock collet. The number of
revolutions must not be higher then the
allowed speed of the router. It is forbidden to
use router bits of diamenters larger than 40
mm.
Carbide tipped bits (HM) are suitable for working hard
materials and enable higher cutting speeds.
Clamping router bits
WARNING: Always disconnect the plug from
power source before making any adjustments
or changing any accessory.
Clamp the bit with the collet
correct order for clamping bits:
Unscrew the nut with the inserted collet on the spindle
by 1-2 threads.
Insert a bit. The bit must be inserted at least 20 mm
deep. Pushing the lock-off button
spindle, and then fasten the clamp nut
wrench
damage the thread on the spindle.
Never drive in the clamp nut
shaft when there is no bit in the collet. Danger of
damaging the collet!
When removing the bit with one turn, first loosen the
clamp nut
is completely loose.
Changing clamping collet
Collet must be fixed in the clamp nut
to change it, pull it from the nut using a small screwdriver
which you insert between the nut and the collet.
on
a new collet with a strong push into the clamp nut (click).
.
Warning: Collet must be inserted in the nut in such
manner that the nut and the collet are even at the
front side.
.
14
until it snaps between the motor
.
with the hose can be
in the direction
. Press the lock
that much to release it and
and the nut
. Excessive fastening of the nut can
, and then continue unscrewing it till the bit
in the
, and then push
Take off the hose of
on the
. Then take off the
. The
you block the
with the fork
till the end of the
. When you want
. Insert