STEP 1
Remove the soft-close
mechanism as shown in Figure
1A. Attach the slide feet to the
bottom of the slide using (4)
M4 screws (See Fig. 1B).
NOTE: You will need to
remove the inner member(s)
from the slide so you have
a hollow channel when
attaching the feet.
STEP 2
Place the Bottom Slide
Template in the bottom of your
cabinet as shown in Figure
2A. Mark (12) hole locations
as shown on the template and
drill 1/8" pilot holes. Align the
front of the slide with the front
of the face frame and center
the slide in the cabinet. Attach
to the floor using (8) #8 1"
wood screws (See Fig. 2B).
NOTE: When using the
template to align the pilot
holes, be sure to fold along
the dotted line on the front
of the template to wrap over
the face frame or front end
of the frameless cabinet. This
will keep your slide from
being installed too far back
into the cabinet.
STEP 3
The top slide of the pantry
needs to be mounted flush
with the face frame. To do
so, it may be necessary to cut
and attach a spacer board as
shown in Figure 3.
2
FIGURE 1A
#2
1
8
(A)
(A)
MEASURE FACE
MEASURE FACE
FRAME WIDTH
FRAME WIDTH
Customer Service: 800-626-1126 | rev-a-shelf.com
FACE FRAME CABINETS
Install bottom slide
1)
Attach feet (#9) to bottom slide (C) using M4 screw (#8) as shown
FIGURE 2A
in
. 1
o T
t a
a t
h c
h t
e
e r
r a
to remove the inner member(s) from the slide so you have a hollow
channel when attaching the feet.
5300/5700 SERIES PULLOUT PANTRY BOTTOM SLIDE TEMPLATE
C
C
cutting line for small cabinet
2)
Mark
12
hole locations and drill ⁄
front of the slide with the front of the face frame and center the slide
n i
h t
e
a c
b
n i
. t e
t A
a t
h c
o t
h t
e
template to align the pilot hole, be sure to fold across the dotted line
on the front of the template to wrap over the face frame or front end
of the frameless cabinet. This will keep your slide from being installed
too far back into the cabinet. See
FIGURE 3
Insert pantry frame
5)
The bottom of the frame (A) sits on top of the bottom slide (C) as
shown in
. 5
U
e s
M
6
c s
AT LEAST 8"
AT LEAST 8"
A
(B)
(B)
(A)
(A)
CORRESPONDING SPACER
CORRESPONDING SPACER
BOARD DIMENSIONS
BOARD DIMENSIONS
6)
Slide the top portion of the frame up so that the top slide is
concealed but not touching the wood cabinet.
FIGURE 1B
o f
o
, t
h t
e
o s
t f
c -
o l
e s
w
l i
n l
e e
d
o t
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
cutting line for small cabinet
CENTER LINE
p "
t o l i
h
o
e l
. s
R
o
u
g
h
y l
using screws (#7). When using the
2.
FIGURE 2B
(120)
(60)
(25)
(B)
(B)
MEASURE
MEASURE
CABINET
CABINET
DEPTH
DEPTH
e r
w
# (
) 2
n a
d
w
a
h s
r e
# (
) 3
o t
a
t t
3
C
Install
3)
T
b
e
a f
e c
as sh
M
4)
a
g i l
n
h t
e
U
Roug
T-5700-BTM-0117
n a
d
step
(60)
(190)
(60)
c a
. h
