Honeywell OmniClass 2.0 Guia De Instalacion
Ocultar thumbs Ver también para OmniClass 2.0:
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 12

Enlaces rápidos

INSTALLATION GUIDE
Parts
1 – OmniClass Reader
1 – Installation Guide
2 – #6-32 x .375" Phillips machine screws
3 – #6-32 x .375" spanner security screw
2 – 7-pin Terminal connectors for terminal readers
1 – 10-pin Terminal connector
Specification
BASE PART
PRODUCT
NUMBER
OM30/OM32 (R10)
900N
7
OM31/OM33 (RP10)
900P
7
OM15/OM17 (R15)
910N
7
OM16/OM18 (RP15)
910P
7
OM40/OM42 (R40)
920N
7
OM41/OM43 (RP40)
920P
7
OM55/OM57 (RK40)
921N
7
OM56/OM58 (RPK40)
921P
7
1 Communication protocols other than Wiegand or Clock & Data (for control
panels), as well as credential interfaces over BLE (not applicable for 9xxL
models), require an additional hardware module which increases current
by 40mA.
2 Standby AVG - RMS current draw without a card in the RF field.
3 Maximum AVG - RMS current draw during continuous card reads. Not
evaluated by UL.
Bluetooth Specifications
OPERATING TEMPERATURE
-15° to 150° F (-25° to 65° C)
The final product, containing the modular transmitter must be labeled with its own FCC ID and IC ID. If the FCC & IC ID is not visible, when the module is installed inside
another device, then the final assembly label must contain the FCC and IC ID numbers with a statement such as follows: "Contains Transmitter Module with FCC ID JQ6-
ICLASSBTM and IC ID 2236B-ICLASSBTM".
This Installation Guide is for informational purposes only. Honeywell makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output are fictitious.
Specifications are subject to change without notice.
INSTALLATION GUIDE
Recommended
• Cable, 5-9 conductor (Wiegand or Clock-and-Data), 4 conductor Twisted Pair Over-All Shield and UL
approved, Belden3107A or equivalent (OSDP)
• Linear DC power supply
• Metal or plastic junction box
• Security tool (for anti-tamper screw) HID 04-0001-03
• Drill with various bits for mounting hardware
• Mounting hardware
• Reader spacer when mounting on or near metal or metal junction boxes - see How to Order Guide
• IP65 Mounting gasket, recommended for outdoor installation
• Back box
CURRENT
INPUT
VOLTAGE (VDC)
STANDBY
MAX AVG
AVG
2
60mA
95mA
75mA
100mA
60mA
95mA
5 - 16VDC
75mA
100mA
65mA
95mA
85mA
100mA
85mA
100mA
5.5 - 16VDC
95mA
105mA
4 Peak - highest instantaneous current draw during RF communication.
5 When configured for Bluetooth Operating Range is -13° to 150° F
(-25° to 65° C)
6 Wiegand Cable Lengths:
100 ft (30.5 m) 22 AWG @ 5 - 6.4VDC
500 ft (152 m) 22 AWG @ 6.5 - 16VDC
7 Mobile Enabled Products, see specifications below.
FREQUENCY
2.4 - 2.480 GHz
1
OPERATING
TEMPERATURE
5
PEAK
3
4
Wiegand = 500 ft - 22 AWG (152 m)
200mA
-30° to 150° F
(-35° to 65° C)
220mA
Page 1
PLT-01558, Rev A.1
CABLE LENGTH
6
Communication Lines
300 ft - 24 AWG 91 m)
RS-485 = Max bus length
4000 ft - 24 AWG (1,219 m)
Max length between nodes:
1640 ft - 24 AWG (500m)
UL Reference Number Deciphering
x
Reader Colors:
K = Black
1
x
Wiring:
N = Pigtail
2
T = Terminal
5 = 5 meter Pigtail
x
Communications:
N = No Module
3
R = RS-485 (OSDP)
L = Indala Prox
B = Bluetooth
FCC & IC IDS
FCC-ID: JQ6-ICLASSBTM
IC-ID: 2236B-ICLASSBTM
PLT-01558, Rev A.1
REGULATORY
REF NUMBER
R10Ex
x
x
1
2
3
RP10Ex
x
x
1
2
3
R15Ex
x
x
1
2
3
RP15Ex
x
x
1
2
3
R40Ex
x
x
1
2
3
RP40Ex
x
x
1
2
3
RK40Ex
x
x
1
2
3
RPK40Ex
x
x
1
2
3
Tabla de contenido
loading

Resumen de contenidos para Honeywell OmniClass 2.0

  • Página 1 ICLASSBTM and IC ID 2236B-ICLASSBTM”. This Installation Guide is for informational purposes only. Honeywell makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output are fictitious. Specifications are subject to change without notice.
  • Página 2: Optional Features

    The facility code needs to be manually entered as 3 digits (i.e. if facility code is 10 P2-6 GPI02/OSDP (RS485-FDX-HDX-B) enter 0-1-0-#). Note: OmniClass 2.0 readers only use facility codes between 1-255, and there is no default facility code. Once the facility code has been entered, the LED Violet...
  • Página 3 OmniClass 2.0 OM15/16/17/18, OM30/31/32/33, OM40/41/42/43, OM55/56/57/58 R10E/RP10E/R10MA/RP10MA, R15E/RP15E/R15MA/RP15MA, R40E/RP40E/R40MA/RP40MA, RK40E/RPK40E/RK40MA/RPK40MA 以下部分是翻译成简体中文的安装指南。 部件 推荐 1 - OmniClass 2.0 读卡器 · 缆线,5-9 导体(Wiegand 或 Clock-and-Data)4 导体双绞线全屏蔽且经过 UL 认 证,Belden 3107A 或同等产品 (OSDP) 1 - 安装指南 2 - #6-32 x .375” 十字机械螺丝 · 线性直流电源...
  • Página 4 R10E/RP10E/R10MA/RP10MA, R15E/RP15E/R15MA/RP15MA, R40E/RP40E/R40MA/RP40MA, RK40E/RPK40E/RK40MA/RPK40MA 以下是翻譯成繁體中文的安裝指南: 推荐 零組件 · 纜線、5-9 導體 (Wiegand 或時脈資料)、4 導體雙絞線全屏蔽和 UL 認 1 - OmniClass 2.0 讀取器 證,Belden3107A 或同等者 (OSDP) 1 - 安裝指南 Guide · 線性 DC 電源供應器 2 - #6-32 x .375” 十字機械螺絲 3 - #6-32 x .375” 扳手安全螺絲...
  • Página 5: Fonctionnalités En Option

    P2-1 GPIO4 (RS485-FDX-Y) Remarque : les précédents lecteurs OmniClass comportaient un câblage RS-485 inversé ( P2-7 et P2-6 - A et B). Lors de la mise à niveau vers un lecteur OmniClass 2.0, effectuez les connexions appropriées comme indiqué ci-dessous.
  • Página 6: Optionale Funktionen

    P2-1 GPIO4 (RS485-FDX-Y) Hinweis: Frühere OmniClass Leser hatten umgekehrte RS-485 Verdrahtung ( P2-7 & P2-6 - A & B). Bei einem Upgrade auf einen OmniClass 2.0 Leser achten Sie auf ordnungsgemäße Anschlüsse wie unten definiert. Hinweis: Es ist möglich, eine vorhandene Wiegand-Verdrahtung für OSDP zu verwenden. Einfache verseilte Kabel, die für Wiegand-Zutrittskontrollleser typisch sind, erfüllen in der Regel jedoch nicht die RS-485-Empfehlungen für Kabel mit verdrillten Aderpaaren.
  • Página 7: Elenco Parti

    HTOG Wiegand e Clock and data. Nota: i lettori OmniClass precedenti hanno invertito il cablaggio RS-485 ( P2-7 & P2-6 - A & B). Quando si passa a un lettore OmniClass 2.0, verificare la correttezza dei collegamenti come descritto di seguito.
  • Página 8 場合は、最終組み立てラベルに次のように FCC ID 番号と IC ID 番号を含める必要があります。「FCC ID JQ6-ICLASSBTM および IC ID 2236B-ICLASSBTM のトランスミッターモジュー ル搭載」。 英語版の 2 ページ目にある次の手順についての図をご覧ください。 取り付け 注意 • 接続ボックスは含まれていません 注: 以前の OmniClass リーダーは、RS-485 の配線が逆でした(P2-7 & 取り扱いの際の注意事項を守ってください • ガスケット(オプション) P2-6 - A & B)。OmniClass 2.0 リーダーにアップグレードするときは、以下 静電気に敏感なデバイス 配線 に示した通りの適切な接続を行ってください。 注:OSDP に既存の Wiegand 配線を再利用することは可能です。しか ピグテール 端子 説明 ピグテール...
  • Página 9 OmniClass 2.0 OM15/16/17/18, OM30/31/32/33, OM40/41/42/43, OM55/56/57/58 R10E/RP10E/R10MA/RP10MA, R15E/RP15E/R15MA/RP15MA, R40E/RP40E/R40MA/RP40MA, RK40E/RPK40E/RK40MA/RPK40MA 다음 섹션은 한국어로 번역한 설치 가이드입니다. 구성품 권장 OmniClass 2.0 Reader 1개 • 케이블, 5-9 도체(Wiegand 또는 Clock & Data), 4 도체 전체 차폐 및 UL 인증 설치 가이드 1개 꼬임 쌍선, Belden 3107A 또는 동급(OSDP) #6-32 x 0.375인치 Phillips 기계 나사 2개 • 선형 DC 전원 공급 장치 #6-32 x 0.375인치 스패너 보안 나사 3개 • 금속 또는 플라스틱 정션 박스 7핀 터미널 커넥터 2개 • 보안 도구(안티 탬퍼 나사용) HID 04-0001-03 10핀 터미널 커넥터 1개 • 장착 하드웨어용으로 다양한 날이 포함된 드릴 • 장착 하드웨어 • 금속 정션 박스 또는 금속 위 및 인근에 장착 시 사용되는 리더 스페이서 - 리더 및 자격 증명 주문 방법 설명서 참조 • IP65 장착 개스킷, 옥외 설치에 권장 • 후면 상자 사양...
  • Página 10: Especificações

    P2-1 GPIO4 (RS485-FDX-Y) Nota: Os leitores OmniClass anteriores tinham uma fiação RS-485 invertida (P2-7 e P2-6 – A e B). Ao atualizar para um leitor OmniClass 2.0, verifique se as conexões estão corretas conforme definido abaixo. Nota: É possível reutilizar cabos Wiegand para OSDP. No entanto, usar um fio flexível simples, normalmente utilizado em leitores com controle de acesso Wiegand, provavelmente não atenderá...
  • Página 11 P2-1 GPIO4 (RS485-FDX-Y) Примечание. Предыдущие модели считывателей OmniClass имели схему RS-485 с обратным подключением (P2-7 и P2-6 — A и B). При переходе на считыватель OmniClass 2.0 убедитесь в правильности подключений, как указано ниже. Примечание. Допускается повторное использование имеющихся кабелей с интерфейсом Wiegand для работы с протоколом OSDP. Однако типичные многожильные кабели, которые...
  • Página 12: Lista De Componentes

    Instalación del Lector en la Placa Posterior Nota: Lectores OmniClass anteriores tenían el cableado RS-485 invertido (P2-7 y P2-6; A y B). Al cambiar el lector OmniClass 2.0 por uno nuevo, asegúrese de que las conexiones sean las correctas, conforme a las especificaciones que se encuentran a continuación.
  • Página 13 OmniClass 2.0 OM15/16/17/18, OM30/31/32/33, OM40/41/42/43, OM55/56/57/58 R10E/RP10E/R10MA/RP10MA, R15E/RP15E/R15MA/RP15MA, R40E/RP40E/R40MA/RP40MA, RK40E/RPK40E/RK40MA/RPK40MA Regulatory The final product, containing the modular transmitter must be labeled with its own FCC ID and IC ID. If the FCC & IC ID is not visible, when the module is installed inside another device, then the final assembly label must contain the FCC and IC ID numbers with a statement such as follows: “Contains Transmitter Module with FCC ID JQ6-ICLASSBTM and IC ID 2236B-ICLASSBTM”.
  • Página 14 This Installation Guide is for informational purposes only. Honeywell makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output are fictitious. Specifications are subject to change without notice. INSTALLATION GUIDE Page 14 PLT-01558, Rev A.1...

Tabla de contenido