Air King 4TM63C Instrucciones De Funcionamiento Y Manual De Piezas

MODELO 4TM63C/9420C
Horqueta
Perilla del Tubo (Pequeña)
Tubo Superior
Protuberancias
Figura 2
Tubo Inferior
Base
Arandela de Seguridad
Perno
Rayada-5/16"
Figura 3
4. Esté seguro de que la Protuberancia del Tubo Superior quede
alineada con la sección conformada del Tubo Inferior. Insertar el Tubo
Superior/Ensamblado del Ventilador por dentro del Tubo Inferior y
dejarlo que se deslice hasta el fondo del Tubo Inferior. Enroscar una
Perilla del Tubo dentro del Tubo Inferior hasta que toque flojamente el
Tubo Superior. Hacer subir el Tubo Superior/Ensamblado del Ventilador
hasta la altura deseada y apretar FIRMEMENTE la Perilla del Tubo.
OPERACIÓN
1. Para Regular la Altura: Mientras se sostiene el Tubo Superior u la
Cabeza del Ventilador firmemente, aflojar la Perilla del Tubo Inferior.
Regular el Ventilador hacia arriba o hacia abajo hasta la altura
deseada y volver a apretar la Perilla del Tubo FIRMEMENTE.
¡CUIDADO! TENDER EL VENTILADOR DE MANERA QUE DESCANSE
SOBRE SU LADO O SOSTENERLO FIRMEMENTE POR LA PARTE
SUPERIOR CUANDO SE REGULE LA ALTURA. PUEDE OCURRIR
ALGUNA LESIÓN SI EL VENTILADOR NO ESTÁ APOYADO.
2. Para Ajustar el Ángulo de la Cabeza: Mientras se sostiene
firmemente la Cabeza, aflojar las Perillas de la Rejilla en cada lado de
la Horqueta (haciéndolas girar hacia la izquierda). Inclinar la Cabeza
hasta la posición deseada y volver a apretar FIRMEMENTE las
Perillas de la Rejilla.
3. Para Ponerlo en Marcha: Conecte el cable a un dispositivo de toma
de tierra 120v, 60Hz. Seleccione la velocidad de funcionamiento
deseada con el Selector que esté en la parte de atrás del Ventilador.
4. ADVERTENCIA: Este ventilador debe ser usa do solamente en
un ambiente limpo y seco. Si producto esta montdo de alguna
otra manera específica que indica la hoja de instuccíon, purdiera
anularse y no tener valor la garantia del fabricante.
MANTENIMIENTO
ADVERTENCIA: DESCONECTE SIEMPRE EL CORDÓN ANTES DE
INTENTAR REALIZAR CUALQUIER FUNCIÓN DE SERVICIO.
LIMPIEZA: Use un trapo y una solución de jabón suave, tal como
detergente líquido para lavar trastes.
ADVERTENCIA: No use gasolina, bencina, diluyente de pintura ni
limpiadores fuertes en aerosol, ya que éstos dañarán el ventilador.
:
ALMACENAMIENTO Cuando no lo utilice, mantenga el aparato en un
lugar limpio y seco.
EL MOTOR HA SIDO PERMANENTEMENTE LUBRICADO.
Rev D 4/01
All manuals and user guides at all-guides.com
27
16
17
14
12
9
13
10 14
11
8
7
11
5
15
4
9
3
19
18
1
5
8
13
2
6
20
21
24
22
23
LISTA DE REPUESTOS
Ref No. De
Descripción
No. Parte
1 2090044 Tornillo de 6/32 x 1/4 PTH
2 2010130 Botón del Interruptor
3 2010634E Cubierta del Motor
4 2057053 Interruptor
5 2091126B Tornillo de #6 x 5/8 Tipo 25 PTH
6 2050015 Cordón Eléctrico
7 2030021SB Motor
8 5060016 Agujero hexagonal de escuadra de pivote
9 2091162 Tornillo Tipo F #8 x 1/2" PPH
10 5096035 Rejilla Trasera
11 5090045 Tornillo de #10-32 x 1/2 HWH SERR F-ZP
12 2011603 * Perilla de la Rejilla
13 5090032 Inserto hexagonal roscado
14 2011601 * Espaciador de Caucho
15 2011600 Horqueta
16 5082075BK Hélice
17 5090044 Tornillo Prisionero de 1/4-28 x 3/8
18 2011602 * Perilla del Tubo
19 2061020 Tubo Superior
20 2061021 Tubo Inferior
21 5060005BK Base
22 5090035 * Arandela de Seguridad Rayada 5/16"
23 5090034 * Perno de 5/16 x 1-1/4
24 2091410 Pie
25 2091143 Tornillo de #8 x 3/8 Tipo F PPH
26 2070004A Ojo de Buey
27 5096038 Rejilla Delantera
* Articulo Incluyendo el numero de Empaques 5098004
4
OPERATING INSTRUCTIONS & PARTS MANUAL
26
25
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
12
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
DESCRIPTION
The AirKing 20" (50.8 cm) pedestal fan features 3-speed rotary knob
operation with a 3-paddle fan blade and variable height adjustments. This
fan has a permanently lubricated motor with a 9 ft. (2.74 m) 18/3 cord set
and is constructed of sturdy, powder coated steel.
SPECIFICATIONS
Motor ....................................... 120V, 60 Hz
Blade diameter ....................... 20" (50.8 cm)
Speeds .................................... 3
Control .................................... Rotary Switch
Air flow distribution ................. 360°
Approvals ................................ UL Listed. Close mesh fan guard
MODEL
SPEED HIGH
24
CFM 7510
M 3 /s 3.54
RPM 1560
Amps 1.78
Cant. Watts 207
dB A 62
1
1
1 GENERAL SAFETY INFORMATION
1
1. Make certain that the power source conforms to the electrical require-
3
ments of the fan.
1
2. The power cord is equipped with a three-prong grounded plug that
1
must be inserted into a matching receptacle. Under no circumstances
2 must the grounding prong be cut off the plug. Where a two-prong wall
receptacle is encountered, it must be replaced with a properly grounded
4
three-prong receptacle installed in accordance with the National
1
Electrical Code (NEC) and all applicable local codes and ordinances.
3
This work must be done only by a qualified electrician, using copper
2
wire only.
2
WARNING: USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS
2
NOT RECOMMENDED. IMPROPER CONNECTION MAY CREATE
1
THE RISK OF ELECTROCUTION. USE OF SUCH ADAPTERS ARE
1
NOT PERMITTED IN CANADA.
1
3. Where possible, avoid the use of extension cords. If they must be
2
used, minimize the risk of overheating by ensuring that they are UL
1 listed and of the proper gage and length. Never use a single extension
cord to operate more than one fan.
1
4. Do not insert fingers or foreign objects into the fan. Do not block or
1
tamper with the fan in any manner while it is in operation. Do not touch
1
the fan while in operation or just after it has been turned off, as some
1
parts may be hot enough to cause injury.
8
5. Unplug power cord before installing or servicing the fan.
8
WARNING: DO NOT DEPEND UPON THE ON-OFF SWITCH AS THE
1
SOLE MEANS OF DISCONNECTING POWER WHEN INSTALLING OR
1
SERVICING THE FAN. ALWAYS UNPLUG THE POWER CORD.
Rev D 4/01
5084012
20" PEDESTAL FAN
20" (50.8 cm) MODEL 4TM63C/9420C
READ AND SAVE THESE INSTRUCTIONS
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
6. This fan is intended for general use ONLY. It must NOT be used in
potentially dangerous locations such as flammable, explosive, chemi-
cal-laden or wet atmospheres.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT USE THIS FAN WITH ANY SOLID STATE
SPEED CONTROL DEVICE.
CAUTION: BECAUSE OF SIZE AND WEIGHT OF THIS FAN,
MAKE SURE ALL PARTS ARE COMPLETELY ASSEMBLED
ACCORDING TO INSTRUCTIONS. FAILURE TO DO SO COULD
RESULT IN FAN COMING APART DURING OPERATION AND/OR
PERSONAL INJURY.
meets OSHA requirements.
ASSEMBLY
TOOLS REQUIRED FOR ASSEMBLY
4TM63C/9420C
• Hex Wrench (Supplied in Parts Bag)
MED LOW
NOTE: ALL HARDWARE REFERRED TO IN THE INSTRUCTIONS
MAY BE FOUND IN THE SUPPLIED PARTS BAG.
5010 3735
2.36 1.76 1. Lay Fan Head on flat surface, so the front side is facing down. Hold
Yoke so the side with the nut is facing up. Loosely attach one Grill
1041 776
Knob and one Rubber Spacer to the Head Assembly. Attach the other
1.46 1.02
Grill Knob and Rubber Spacer to the Head Assembly and FIRMLY tighten.
167 115 Return to the first Grill Knob and FIRMLY tighten. ( Figure 1 )
55 48
Grill Knob (Large)
Rubber Spacer
Figure 1
NOTE: THE UPPER PIPE HAS 2 BUMPS, ONE AT EACH END. THE
BUMP CLOSER TO THE END OF THE PIPE INDICATES THE TOP.
THIS END FITS INTO THE YOKE.
2. Make sure Bump on Upper Pipe is aligned with formed section of
Yoke. Insert Upper Pipe into Yoke. To ensure fit is tight, twist Upper
Pipe until it is tight inside of Yoke. ( Figure 2 )
NOTE: THE UPPER PIPE SHOULD FIT COMPLETELY INSIDE OF THE YOKE.
1
Rubber Spacer
Grill Knob (Large)
Yoke
Nut
5084012