IRUDEK TIGER 2,5 Instrucciones De Uso página 10

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

6 ATTENTION
- A full body harness is the only acceptable body holding device that can be used in a fall arrest system.
- The fall protection system must only be connected to the harness anchor points identified with the capital letter "A". Iden-
tification "A/2", indicates the need to join the two points showing the same identification together. It is forbidden to connect
the system to a single anchor point identified as "A/2".
- Connection to the anchor point and other equipment must be done through connectors in conformity to EN 362.
- For use with fall arresters in conformity to EN 353-1, EN 353-2 it is recommended to connect the equipment to the front
anchor point on the harness. For use with energy absorbers EN 355 or fall arresters EN 360 it is recommended to connect
the equipment to the back anchor point on the harness.
- Before each use of personal protective equipment it is obligatory to carry out a pre-use check of the equipment, to ensure
that it is in a serviceable condition and operates correctly before it is used.
7 INFORMATION & ADVICE
- A rescue plan shall be in place to deal with any emergencies that could arise during the work.
- It is forbidden to make any alterations or additions to the equipment without the manufacturer´s prior written consent.
- Personal protective equipment shall not be used outside its limitations, or for any purpose other than that for which it
intended.
- Before use ensure about the compatibility of items of equipment when assembled into a system. Ensure that all items
are compatible and appropriate for the proposed application. It is forbidden to use combinations of items of equipment in
which the safe function of any one item is affected by or interferes with the safe function of another. Periodically check the
connection and adjustment of the components to avoid accidental disconnection and loosening.
- Personal protective equipment must be withdrawn from use immediately when any doubt arise about its condition for safe
use and not used again until confirmed in writing by a competent person that it is acceptable to do so.
- Personal protective equipment must be withdrawn from use immediately when it have been used to arrest a fall.
- It is essential for safety to verify the free space required beneath the user at the workplace before each occasion of use
(2M), so that, in the case of a fall, there will be no collision with the ground or other obstacle in the fall path. The required value
of the free space should be taken from instruction manual of used equipment.
- There are many hazards that may affect the performance of the equipment and corresponding safety precautions that
have to be observed during equipment utilization, especially:
• Trailing or looping of lanyards or lifelines over sharp edges,
• Any defects like cutting, abrasion, corrosion
• Climatic exposure,
• Pendulum falls,
• Extreme temperatures
• Chemical reagents,
• Electrical conductivity
-It is essential for the safety of the user that if the product is re-sold outside the original country of destination the reseller
shall provide instructions for use, for maintenance, for periodic examination and for repair in the language of the country in
which the product is to be used.
8 LIFETIME
The estimated product lifetime is 11 years from the date of manufacture (1 year storage + 10 years for use). The following
factors can reduce the lifetime of the product : intense use, contact with chemical substances, specially agressive environ-
ment, extreme temperature exposure, UV exposure, abrasion, cuts, violent impacts, bad use or maintenance.
The required annual examinations will validate the correct functioning of the equipment. It is compulsory that the equipment
is examined by the manufacturer or his authorized representative at least once a year.
In case that it have been used to arrest a fall, the equipment must be withdrawn from use.
9 TRANSPORT
The Personal Protective Equipment must be transported in a package that protects it against moisture or mechanical,
chemical and thermal attacks.
10 INSTRUCTIONS FOR MAINTENANCE
-CLEANING: The personal protective equipment must be cleaned without
causing adverse effect on the materials used in the manufacture of the equipment. For textile ( webbing and ropes ) and
plastic parts wipe with cotton cloth or a soft brush. Do not use any abrasive material. For intensive cleaning wash the har-
ness at a temperature between 30ºC and 60ºC using a neutral detergent. For metallic parts wipe with a wet cloth. When
the equipment becomes wet, either from being in use or when due to cleaning, it shall be allowed to dry naturally, and shall
be kept away from direct heat.
-STORAGE: Personal protective equipment should be stored loosely packed, in a
dry and well- ventilated place, protected from direct light, UV degradation, dust, sharp edges, extreme temperature and
aggressive substances.
11 REPAIR
Any repair shall only be carried out by equipment manufacturer or his authorized representative following manufacturer's
procedures.
12 MARKING
The equipment is marked with the next information :
Tabla de contenido
loading

Tabla de contenido