Commercial Electric SPTM2-2801 Guía De Uso Y Cuidado

Safety Information
Please read and understand these instructions before attempting to install or use this light fixture.
1. This LED fixture is suitable for outdoor use and wet locations.
2. Do not disassemble this LED fixture. There are no user-serviceable parts inside. The LED bulb is not
replaceable.
3. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Pre-Installation
TOOLS AND MATERIALS REQUIRED (NOT INCLUDED)
Philips
Silicone Sealant
Screwdriver
Installation
1
WIRING THE SPOT LIGHT
□ Route the fixture wires through
the cover plate gasket (B).
□ Wire the spot light (A) to the
supply lines in the electrical
box. Connect white to white
(neutral), black to black (live),
and green and yellow to the
ground wire.
□ Secure all wiring connections
with wire nuts (not included).
3
AIMING THE SPOT LIGHT
□ Aim the spot light to the
desired angle by rotating
each lamp up and down,
left and right.
Step Ladder Wire Nuts
B
Item # 1002863235/1002863236/ 1002863239
Model # SPTM2-2801/SPTM2-2803/SPTM2-2802
Use and Care Guide
5-Year Limited Warranty
WHAT IS COVERED
This product is guaranteed to be free of factory defective parts and workmanship
for a period of 5 years from date of purchase. Purchase receipt is required for all
warranty claims.
WHAT IS NOT COVERED
This guarantee does not include repair service, adjustment and calibration due to
misuse, abuse or negligence, or LEDs. Unauthorized service or modification of the
product or of any furnished component will void this warranty in its entirety. This
warranty does not include reimbursement for inconvenience, installation, setup time,
loss of use, unauthorized service, or return shipping charges. No service parts are
available for this product.
Contact the Customer Service Team at 1-877-527-0313 or visit www.homedepot.com.
2
MOUNTING THE SPOT LIGHT
□ Secure the spot light (A) and
the cover plate gasket (B) to
A
the junction box using the two
mounting screws (AA).
□ Apply silicone sealant around
the edges of the fixture and
the jam nuts at the base of the
adjustment arms.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Dual Spot Light
WARNING: Risk of Fire, Electric Shock, or Injury to
Persons. Turn the power off at the circuit breaker or fuse
and install in accordance with local electrical codes.
WARNING: Do not install near flammable material.
NOTE: The cover plate mounts to a recessed
mounted standard junction box. The junction box must
be at least 1-1/2 in. in depth for proper installation.
Please contact 1-877-527-0313 for further assistance.
A
AA
B
HOMEDEPOT.COM