Idiomas disponibles
Idiomas disponibles
5. Manual ON/OFF OVERRIDE
With the door shut, press it inward
to bypass the current settings and
manually turn your attached
devices ON or OFF. Choose
between four override settings:
Display Reads
Override Setting
OFF/MAN (manual)
Attached devices are OFF and will remain off
ON/MAN (manual)
Attached devices are ON an will remain on
OFF/AUTO (automatic)
Attached devices are OFF temporarily, but the
next programmed event will resume.
ON/AUTO (automatic)
Attached devices are ON temporarily, but the
next programmed event will resume.
*
Programmed Events will no longer function as
set. They are being manually overridden.
6. SYSTEM ON/OFF
Locate the "SYSTEM" switch. Sliding the
switch to "OFF" will turn the entire device
off and the timer will no longer operate
the attached devices. NOTE: The clock
and all program settings will remain
stored while the system is OFF. This
setting is convenient for permanently
overriding all settings and turning off
power to the attached devices.
7. One-Touch DAYLIGHT SAVINGS
TIME Setting
Locate the +/- 1 hr Daylight Savings Time
icon
to the right of the "Hour" button.
Press and hold the "Hour" button for
about 4 seconds to adjust the clock for
Daylight Savings. When in daylight
savings mode, the icon "DST" will appear.
Repeat to return to Standard Mode.
NOTE: Use of this button alleviates the need to completely
re-program the clock when there is a time change.
8. One-Touch "RANDOM"
Security Setting
Locate the Random icon
to the right
R
of the "Min" button. Press and hold the
"Min" button for about 4 seconds to enter
or exit the Random Security Setting.
When this setting is activated, the icon
"RND" will appear. NOTE: This function
requires at least one event to be set up
as described in Step 3 above. Timer will randomly turn devices
ON/OFF within 0 - 30 minutes of the programmed settings to
help create that "lived-in" look.
HELPFUL TIPS
• Timer has up to 18 customizable ON/OFF Event Settings to
turn devices on and off at different times and on different
days as programmed.
• To automatically advance through the Hour and Minute
selections, press and hold the "Hour" or "Min" buttons.
IN CASE OF POWER FAILURE
5
ON/AUTO
Timer will continue to operate on battery backup if the power goes out;
however, it will not turn attached devices on or off. Once power is
restored, programming will resume. If power remains out longer than
the battery backup will operate, re-program the timer as explained in
the "Operating Instructions". NOTE: Battery is permanently installed
and not replaceable. It automatically recharges when power is provided
to the timer.
*
*
TROUBLESHOOTING
PROBLEM POSSIBLE
Timer turns
ON/OFF at
incorrect times
6
or skips some
CLR
of the
Reset
programmed
Day
Hour
hr
times.
Prog
Min
om
R
SYSTEM
OFF
ON
The attached
device turns off
immediately
after being
7
turned on.
CLR
Reset
Day
Hour
LCD screen is
hr
blank.
Prog
Min
R
om
SYSTEM
OFF
ON
LCD screen is
on but attached
device is off.
8
CLR
Reset
To avoid fire, shock, or death, turn off power at circuit
Day
Hour
breaker or fuse box before wiring.
hr
om
Prog
Min
R
Installation by a licensed electrician to local, state and national
SYSTEM
codes is recommended. For INDOOR use only. Do not use to
control appliances. Do not attempt to disassemble this timer. Do
OFF
ON
not exceed electrical ratings.
Afin d'éviter les risques d'incendie, de choc électrique ou de
décès, coupez l'alimentation électrique depuis le panneau de
disjoncteurs ou de fusibles avant d'effectuer le câblage.
Nous vous recommandons de faire appel à un électricien agréé afin qu'il
procède à une installation conforme aux codes municipaux, provinciaux
et nationaux. Pour un usage à l'INTÉRIEUR seulement. N'utilisez pas
cet article pour commander des électroménagers. Ne tentez pas de
démonter cette minuterie. Ne dépassez pas les capacités électriques.
CORRECTIVE
CAUSE
ACTION
1. Programmed
1. Press ON/OFF to review
event(s) are incorrect.
the settings and revise
2. Timer is in
them as necessary. See
RANDOM mode,
OPERATING
which varies
INSTRUCTIONS.
switching times up to
2. If you don't want to keep
± 30 minutes (to give
the timer in RANDOM
your home a "lived-in"
mode, press MODE to
look).
change to AUTO mode.
The timer is wired
Disconnect wires, remove
incorrectly.
timer, re-install per the
instruction manual. If
problem persists, contact
certified electrician.
The included
Battery will automatically
rechargeable battery
recharge after installation.
has lost its charge.
The light or attached
Make sure the light or
device itself may be
attached device is switched
switched OFF.
ON and plugged in.
WARNING
AVERTISSEMENT
FCC REGULATORY STATEMENT
WARNING: Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user authority to
operate the equipment.
Notes: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
SAFETY INFORMATION & SPECIFICATIONS
THIS TIMER IS FOR USE WITH A 120 V AC POWER SOURCE.
120 V AC / 60 Hz
DO NOT ATTACH A DEVICE THAT EXCEEDS THE UNIT
RATINGS:
15 A / 1,800 W Resistive (General Purpose)
10 A / 1,200 W Tungsten (Incandescent)
10 A / 1,200 W Ballast (Fluorescent)
1/2 HP (Horsepower Motor)
LIMITED 1 YEAR WARRANTY
Prime warrants this product to be free from manufacturing defects for a
period of one year from the original date of purchase ("warranty period").
This warranty is limited to the repair or replacement of this product only and
Prime is not liable for any consequential or incidental damage to other
products that may be used with this unit. This warranty is effective only if
such unit is returned to Prime not later than thirty (30) days after the
expiration of the warranty period. Warranty is void if damage is due to
neglect, misuse, alteration, modification, improper installation, or repair by
other than Prime. This warranty is in lieu of all other warranties express or
implied. Some states do not allow limitations on how long an implied
warranty lasts or permit the exclusion or limitation of incidental or
consequential damages, so the above limitations may not apply to you.
It is our experience that a product that fails prematurely due to a
manufacturing defect in materials or workmanship, will generally do so very
early in the product's life cycle, often the first or second time the product is
used. Products that are returned for warranty inspection after months or
years of continuous reliable service are usually the result of normal wear
and tear, which is not considered a defect in materials or workmanship and
therefore is not covered by the warranty.
This warranty gives you specific rights, and you may also have other rights
which vary from state to state. If unit should prove defective within the
warranty period, return within the time period set forth above prepaid with
the original purchase receipt to:
Prime Wire & Cable, Inc.
ATTN: Timer Warranty
280 Machlin Court
City of Industry, CA 91789
Printed in China
