Idiomas disponibles
Idiomas disponibles
IMPORTANT
Please read these instructions carefully.
NOTE: The safe operational requirements, warnings and cautions.
1. FORWARD
This engine crane is intended to be used to remove, install and
transport in the lowered position, rated capacity automotive and
light truck engines and engine assemblies. It must be used with
appropriately rated engine leveler, sling and/or chains which are
NOT INCLUDED. After removing, immediately transfer the load
to an appropriately rated work station such as an engine stand.
2. MAIN SPECIFICATIONS
Capacity
Lifting height
Height of crane
Length of height
G.W.
N.W.
Packing size
1#
2#
3. SAFETY INSTRUCTIONS
1. Keep work area clean.
2. Observe work area conditions.
3. Keep children away.
4. Store idle equipment.
5. Use the right tool for the job.
6. Dress properly.
7. Use eye protection.
8. Do not overreach.
9. Maintain tools with care.
10. Stay alert.
11. Check for damaged parts.
12. Replacement parts and accessories.
13. Do not operate tool if under the influence
of alcohol or drugs.
14. Never exceed the maximum lifting capacity.
Beware of Dynamic Loading!
15. Maintenance.
16. Not to be used for aircraft purposes.
17. Do not attempt to move the Crane when under load.
4. ASSEMBLY
To Attach The Large Casters To The Rear Of The Base:
To Attach The Small Casters To The Front Of The Base:
To Attach The Large Casters To The Legs:
To Attach The Legs To The Base:
To Attach The Support Post And Support Braces To The Base:
To Attach The Boom To The Support Post:
To Attach The Boom Extension To The Boom:
To Attach The Chain/Hook Assembly To The Boom Extension:
To Attach The Hydraulic Ram To The Support Post And Boom:
500 - 2,000 kg.
2,380 mm.
1,450 mm.
1,550 mm.
58 - 95 kg.
56 - 93 kg.
1,310 x 840 x 90 mm.
1,320 x 300 x 160 mm.
5. OPERATION INSTRUCTION
1. To raise the Extension Boom, close the Release Valve on the
Hydraulic Ram. Then, pump the Handle until the Extension
Boom reaches the desired height.
2. To extend the length of the Extension Boom, remove bolt and
nut. Pull out on the Extension Boom until the desired extension
hole in the Boom aligns with the hole in the Extension Boom.
Then re-insert the bolt through the holes in the Boom and
Extension Boom, and lock the bolt in place with the nut.
3. WARNING! Do not exceed the maximum lifting capacities of
this tool. Exceeding the maximum lifting capacities could
cause personal injury and/or property damage. The longer
the Extension Boom is extended, the lower the lifting capacity
of this Shop Crane.
4. Position the Shop Crane so that the Hook is directly above
the object you wish to lift.
5. WARNING! Stay clear of the Shop Crane. Never go under an
object being lifted by the Crane. It is possible for the Hook to
slip, causing an object to fall, possibly resulting in serious
injury and/or property damage. Always monitor the object
being lifted so it does not rock back and forth.
6. Open the Release Valve slightly to lower the Hook. Attach
the Hook to the object you are lifting, and make sure the
Safety Latch on the Hook is fully closed. Then close the
Release Valve, and pump the Handle to raise the object.
Carefully move the Shop Crane to the location where you
wish to lower the object, i.e., an engine stand, proper support,
floor surface, etc. Then lower the object by opening the
Release Valve slightly.
7. Once the object is fully lowered, disconnect the Hook from
the object. Then store the Shop Crane (unfolded or folded)
in a clean, dry, safe location out of reach of children and other
unauthorized people.
6. MAINTENANCE
1. Check all of the mounting hardware before each use and
make sure it is secure before using the Shop Crane.
2. Make sure the Hook & Chain are clean of dirt, grease,
or debris.
3. If the Jack is not performing to satisfaction, there may be air
in the hydraulic system. To purge the system of air, follow
these instructions.
a. Make sure the Ram is completely lowered.
b. Remove the Oil Fill Plug and top off with Hydraulic Fluid.
c. Raise the Ram to maximum height.
d. Loosen the Release Valve and push the Ram all the way
down.
e. Top off with Hydraulic Fluid and replace the plug. Repeat
if necessary.
4. To clean, use a damp cloth and a mild detergent. Do not use
solvents or other flammable agents.
5. If lifting performance of the Shop Crane begins to diminish,
check the hydraulic oil level in the Oil Tank. If necessary, top
off the Oil Tank with hydraulic oil.
