Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Product Assemblies
SP-DBMUBSC-8-FN
SP-DBMUBSC-17-FN
SP-DBMUBSC-11-FN
SP-DBMUBSC-20-FN
SP-DBMUBSC-14-FN
Fully extend slides. Mount 1 – left hand
1
slide and 1 – right hand slide to the bottom
slide mounting holes in the upright brackets
using 8 – #6-32 X 5/16" screws. Repeat this
process for upper slides (1).
NOTE: There are 4 upper basket mounting
locations. Install upper slides at desired height.
Attach rear slide brackets to upper slides
2
by pushing bracket firmly onto slides (2).
NOTE: No rear slide brackets are needed
for lower slides.
Place slide and upright bracket assembly
3
into cabinet so that the front edges of the
slides are flush with the front of the cabinet
opening on the opposite side of cabinet door
hinges. Extend the upper drawer slide.
Double-tier Pullout Baskets
Inspect all parts and read all instructions prior to beginning assembly and installation.
Tools Required
• Phillips Head Screwdriver
• Tape Measure
Parts Included
Upper Basket (1)
Lower Basket (1)
Upright Brackets (2)
1
If a half shelf is
present in cabinet
mount the rear
upright bracket
here.
2
Installation Instructions
Left Hand Slides (2)
Right Hand Slides (2)
Cross-Brace (1)
DBLSC-CBAR + PRODUCT SIZE
Left Slide
3
Flush
#6-32 x 5/16" Screws (18)
HP-DBL-BRKT
#8 x 3/4" Wood Screws (4)
HP-DBL-BRKT
#6 x 1/2" Wood Screws (7)
HP-DBL-BRKT
Rear Slide Brackets (2)
HP-DBL-BRKT
Right Slide
Resumen de contenidos para simplyput SP-DBMUBSC-8-FN
- Página 1 HP-DBL-BRKT Upright Brackets (2) Cross-Brace (1) DBLSC-CBAR + PRODUCT SIZE Rear Slide Brackets (2) Product Assemblies HP-DBL-BRKT SP-DBMUBSC-8-FN SP-DBMUBSC-17-FN SP-DBMUBSC-11-FN SP-DBMUBSC-20-FN SP-DBMUBSC-14-FN Fully extend slides. Mount 1 – left hand slide and 1 – right hand slide to the bottom slide mounting holes in the upright brackets using 8 –...
- Página 2 Push the slide back so that the mounting hole is accessible. Install 1 – #6 x 1/2" wood screw (4). Ensure that upright brackets are parallel to the front of the cabinet then attach to the base of the cabinet with 4 – #8 x 3/4" wood screws (5A).
- Página 3 Assemblages Ensamblaje Soportes verticales (2) Abrazadera cruzada (1) de productos DBLSC-CBAR + TAMAÑO DEL PRODUCTO Soportes traseros deslizantes (2) SP-DBMUBSC-8-FN SP-DBMUBSC-17-FN HP-DBL-BRKT SP-DBMUBSC-11-FN SP-DBMUBSC-20-FN SP-DBMUBSC-14-FN Extienda del todo las guías deslizantes. Fije 1 guía izquierda y 1 derecha a los orificios inferiores de montaje que hay en los soportes verticales usando 8 tornillos #6-32 X 7.9 mm...
- Página 4 Empuje la guía deslizante hacia atrás, de manera que pueda acceder al orificio de montaje. Coloque 1 tornillo para madera #6 x 12.7 mm (1/2") (4). Asegúrese de que los soportes verticales están paralelos a la parte frontal del armario cuando los una a la base del armario con 4 tornillos para madera #8 x 19 mm (3/4") (5A).